AKO D14918 Programming Key Instruction Manual

D149H181 Ed.08

AKO-D14918

Mae'r AKO-D14918 programming key allows you to quickly and easily copy configured settings from one controller to another with the same functionality

Rhybuddion

-Using the equipment without following the manufacturer’s instructions may affect the device’s safety requirements.
-The unit must be used in a location protected from vibrations, water and corrosive gases, where the ambient temperature does not exceed that shown in the technical data.
-Connecting this key to unsupported devices (see table) can cause serious damage to both pieces of equipment.
-In equipment with active communication, log out of communications software or disconnect the cable before connecting the programming key. The communication controller’s address must be 1.

Disgrifiad

1. COM LED
2. ALLWEDD COFNOD
3. EXTERNAL POWER CONNECTOR
4. READ KEY
5. LED AR
6. CONNECTOR CABLE

Cydweddoldeb

Refer to the instruction manual of your equipment on its compatibility with the AKO-D14918 programming key.

Connecting incompatible devices can permanently damage the key.

Gwifrau

1. PWYSIG: Pay attention to the orientation of the connector.
2. AKO-80018 
   (Dewisol)
3. AKO-D14918

Cyflenwad pŵer

-If the controller is in operation (on-site programming), the key does not require an external power supply (it is powered via the connecting cable).
-If the controller is NOT powered (workshop programming), the key requires a 12Vdc/500 mA external power supply (AKO-80018 or equivalent).

Gweithrediad

PWYSIG: After connecting the key to the equipment wait for 5 seconds before starting the reading or writing process.

RECORD key

Write the data contained in the key memory to the controller.
Keep the key pressed until the COM led starts flashing quickly.
When recording is complete the controller will reset.

READ key

It reads the data from the controller and stores them in the programming key.
Keep the key pressed until the COM led starts flashing quickly.
When recording is complete the controller will reset.

LED AR

Steady or flashing: Indicates that the key is connected to the controller.

COM LED

Sefydlog: Indicates an error in the transmission/reception of data
Fflachio cyflym: Indicates transmission/reception of data in progress. At the end of the transmission COM LED bydd yn diffodd.
Fflachio araf: Indicates compatibility error- the data contained in the memory of the key is not compatible with the model of controller connected. Data can only be read from the controller to the key.

NODYN: To restart after a transmission or compatibility error, turn off the power supply or disconnect the controller connector cable.

PWYSIG: Byth disconnect the programming key during data transmission.

Manylebau technegol

Length of cable from programming key to controller . . . . . . . . . . . . . 300 mm
Cyflenwad cyftage . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . 12 Vdc nominal
Supply current . . . . . . . . . . . . . . . . . . . . . . . . . . . . AKO-80018 / 500 mA máx.
Manylebau amgylcheddol:
Ambient working temperature. . . . . . . . . . . . . . . . . . . . . . . . . . . . 0ºC to 50ºC
Storage temperature . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . . -30ºC to 70ºC

AKO ELECTROMECÁNICA, SA
Av. Roquetes, 30-38 | 08812 Sant Pere de Ribes | Barcelona | España

35D149181 REV.07 2025

Rydym yn cadw'r hawl i gyflenwi deunyddiau a allai amrywio ychydig i'r rhai a ddisgrifir yn ein Taflenni Technegol.
Mae gwybodaeth wedi'i diweddaru ar gael ar ein websafle.