Rhaglennydd Modiwl XTOOL X2MBIR
Ymwadiad
Please read this manual carefully before using X2Prog Module Programmer (herein after referred to as X2Prog). Shenzhen Xtooltech Intelligent Co., Ltd. (herein after referred to as “Xtooltech”) does not assume any liability in case of misuse of the product. Pictures illustrated here are for reference only and this user manual is subject to change without prior notice.
Disgrifiad o'r Cynnyrch
Mae X2Prog yn Rhaglennydd Modiwlau sy'n gallu darllen, ysgrifennu ac addasu data sglodion EEPROM ac MCU trwy'r dull BOOT. Mae'r ddyfais hon yn addas ar gyfer tiwnwyr neu fecanyddion cerbydau proffesiynol, sy'n darparu swyddogaethau fel clonio modiwlau, addasu, neu amnewidiadau ar gyfer ECU, BCM, BMS, dangosfyrddau neu fodiwlau eraill. Mae X2Prog hefyd yn gallu defnyddio modiwlau ehangu eraill a ddarperir gan Xtooltech, gan alluogi hyd yn oed mwy o swyddogaethau fel rhaglennu BENCH, codio trawsatebydd a llawer mwy.
Cynnyrch View
- ① DB26 Port: Use this port to connect with cables or wiring harnesses.
- ② Indicators: 5V (Red / Left): This light will be turned on when X2Prog receives 5V power input. Communication (Green / Middle): This light will be flashing when the device is communicating. 12V (Red / Right): This light will be turned on when X2Prog receives 12V power input.
- ③ ④ Expansion Ports: Use these ports to connect with other expansion modules.
- ⑤ 12V DC Power Port: Connect to 12V power supply when necessary.
- ⑥ USB Type-C Port: Use this USB port to connect with XTool devices or PC.
- ⑦ Nameplate: Show product information.
Gofynion Dyfais
- XTool devices: APP version V5.0.0 or higher;
- Cyfrifiadur personol: Windows 7 neu uwch, 2GB o RAM
Cysylltiad Dyfais
Ehangu a Chysylltiad Cebl
X2Prog is adapted to various expansion modules or cables for extra functions. Different modules are needed in different situations.
To install expansion modules, directly connect the modules to X2Prog using the expansion ports (32/48PIN) or the DB26 port.
Multiple expansion modules can be installed on X2Prog at the same time. When you are operating, check the device and see which modules are necessary.
Sut i Ddarllen ac Ysgrifennu EEPROM
Trwy Fwrdd EEPROM
*EEPROM Board only comes with X2Prog standard pack.
When reading EEPROM in this method, the chip should be taken off from the ECU and needs to be soldered onto the EEPROM board.
Mae yna ffyrdd eraill o ddarllen EEPROM gan ddefnyddio modiwlau ehangu. Gwiriwch y diagramau ar yr ap a gweld sut allwch chi gysylltu â'r sglodion.
Sut i Ddarllen ac Ysgrifennu MCUs
BOOT
When reading MCU in this method, the wiring harness should be soldered to the ECU board according to the wiring diagram, and a 12V power supply should be connected to X2Prog.
Wrth ddarllen MCU yn y dull hwn, dylid plygio'r harnais gwifrau i borthladd yr ECU yn ôl y diagram gwifrau, a dylid cysylltu cyflenwad pŵer 12V ag X2Prog.
Cysylltwch â NI
- Gwasanaethau Cwsmeriaid:
cefnogi@xtooltech.com - Swyddogol Websafle:
https://www.xtooltech.com/ - Cyfeiriad:
17 a 18/F, Adeilad A2, Dinas Greadigol, Liuxian Avenue, Ardal Nanshan, Shenzhen, Tsieina - Corporate & Business:
marchnata@xtooltech.com
© Shenzhen Xtooltech Intelligent Co., Ltd. Copyright, All Rights Reserved
Gwybodaeth Cydymffurfiaeth
Cydymffurfiaeth Cyngor Sir y Fflint
FCC ID: 2AW3IM604
Mae'r ddyfais hon yn cydymffurfio â Rhan 15 o Reolau Cyngor Sir y Fflint. Mae gweithredu yn amodol ar y ddau amod canlynol:
- Efallai na fydd y ddyfais hon yn achosi ymyrraeth niweidiol
- Rhaid i'r ddyfais hon dderbyn unrhyw ymyrraeth a dderbynnir, gan gynnwys ymyrraeth a allai achosi gweithrediad annymunol.
Rhybudd
Gallai newidiadau neu addasiadau nad ydynt wedi'u cymeradwyo'n benodol gan y parti sy'n gyfrifol am gydymffurfio ddirymu awdurdod y defnyddiwr i weithredu'r offer.
Nodyn
Mae'r offer hwn wedi'i brofi a chanfuwyd ei fod yn cydymffurfio â'r terfynau ar gyfer dyfais ddigidol Dosbarth B, yn unol â Rhan 15 o Reolau Cyngor Sir y Fflint. Mae'r terfynau hyn wedi'u cynllunio i ddarparu amddiffyniad rhesymol rhag ymyrraeth niweidiol mewn gosodiad preswyl.
This equipment can generate, use and radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Ailgyfeirio neu adleoli'r antena sy'n derbyn.
- Cynyddu'r gwahaniad rhwng yr offer a'r derbynnydd.
- Cysylltwch yr offer ag allfa ar gylched sy'n wahanol i'r hyn y mae'r derbynnydd wedi'i gysylltu ag ef.
- Cysylltwch â'r deliwr neu dechnegydd radio/teledu profiadol am gymorth.
Datganiadau Rhybudd Amlygiad RF:
Mae'r offer hwn yn cydymffurfio â therfynau amlygiad ymbelydredd Cyngor Sir y Fflint a osodwyd ar gyfer amgylchedd heb ei reoli. Rhaid gosod a gweithredu'r offer hwn gyda lleiafswm pellter o 20cm rhwng y rheiddiadur a'r corff.
Plaid Cyfrifol
- Company name: TianHeng Consulting, LLC
- Cyfeiriad: 392 Andover Street, Wilmington, MA 01887, Unol Daleithiau
- E-bost: tianhengconsulting@gmail.com
Datganiad IED
- IC: 29441-M604
- PMN: M604, X2MBIR
- HVIN: M604
Mae'r ddyfais hon yn cynnwys trosglwyddydd(wyr)/derbynnydd(wyr) sydd wedi'u heithrio rhag trwydded sy'n cydymffurfio â RSS(au) sydd wedi'u heithrio rhag trwydded Arloesi, Gwyddoniaeth a Datblygu Economaidd Canada.
CAN ICES (B) / NMB (B).
This device meets the exemption from the routine evaluation limits in section 6.6 of RSS 102 and compliance with RSS 102 RF exposure, users can obtain Canadian information on RF exposure and compliance. This equipment complies with Canada radiation exposure limits set forth for an uncontrolled environment. This equipment complies with IC exposure limits set forth for an uncontrolled environment. This equipment shall be installed and operated with minimum distance 20cm between the radiator & body.
Datganiad cydymffurfio
Hereby, Shenzhen XTooltech Intelligent Co., Ltd declares that this Module Programmer is in compliance with the essential requirements and other relevant provisions of Directive 2014/53/EU. In accordance with Article 10(2) and Article 10(10), this product allowed to be used in all EU member states.
UKCA
Hereby, Shenzhen XTooltech Intelligent Co., Ltd declares that this Module Programmer satisfies all the technical regulations applicable to the product within the scope of UK Radio Equipment Regulations (SI 2017/1206); UK Electrical Equipment (Safety) Regulations (SI 2016/1101); and UK Electromagnetic Compatibility Regulations (SI 2016/1091) and declare that the same application has not been lodged with any other UK Approved Body.
FAQ
- C: Beth yw gofynion y ddyfais ar gyfer defnyddio'r Modiwl X2MBIR Rhaglennydd?
A: The X2MBIR Module Programmer requires XTool devices with APP version V5.0.0 or higher and a PC running on Windows 7 or higher with a minimum of 2GB RAM. - C: Sut ydw i'n darllen ac yn ysgrifennu data EEPROM gyda'r X2Prog?
A: To read and write EEPROM data, use the provided EEPROM Board included in the standard pack. Remove the chip from the ECU and solder it onto the EEPROM board. - C: A allaf ddefnyddio modiwlau ehangu lluosog ar yr un pryd â'r X2Prog?
A: Yes, multiple expansion modules can be installed on X2Prog at the same time. Ensure you connect them correctly to enhance functionality.
Dogfennau / Adnoddau
 |
Rhaglennydd Modiwl XTOOL X2MBIR [pdfCanllaw Defnyddiwr M604, Rhaglennydd Modiwl X2MBIR, X2MBIR, Rhaglennydd Modiwl, Rhaglennydd |