Generadur Swyddogaeth Gyflafaidd Tektronix AFG1062

Gwybodaeth bwysig
Mae'r nodiadau rhyddhau hyn yn cynnwys gwybodaeth bwysig am fersiwn 1.2.0 o feddalwedd AFG1062.

Rhagymadrodd

Mae'r ddogfen hon yn darparu gwybodaeth atodol ynghylch ymddygiad meddalwedd AFG1062. Mae'r wybodaeth hon wedi'i grwpio i chwe chategori:

Hanes adolygu	Yn rhestru fersiwn meddalwedd, fersiwn y ddogfen, a dyddiad rhyddhau'r feddalwedd.
Nodweddion / gwelliannau newydd	Crynodeb o bob nodwedd newydd arwyddocaol wedi'i chynnwys.
Datrys problemau	Summary of each significant software/firmware bug fix.
Problemau hysbys	Disgrifiad o bob problem hysbys hysbys a ffyrdd o weithio o'i chwmpas.
Cyfarwyddiadau gosod	Cyfarwyddiadau manwl yn disgrifio sut i osod y feddalwedd.
Atodiad A - Fersiynau blaenorol	Information about previous versions of the software.

Hanes adolygu
Mae'r ddogfen hon yn cael ei diweddaru a'i dosbarthu o bryd i'w gilydd gyda datganiadau a phecynnau gwasanaeth i ddarparu'r wybodaeth fwyaf diweddar. Mae'r hanes adolygu hwn wedi'i gynnwys isod.

Dyddiad	Fersiwn meddalwedd	Rhif y ddogfen
9/1/2025	v1.2.0	077187500
8/8/2024	v1.1.0	–
10/29/2019	v1.0.9	–
5/27/2018	v1.0.6   v1.0.5	–   –
4/23/2017	v1.0.4   v1.0.3   v1.0.2	–   –   –

FERSIWN 1.2.0

Nodweddion / gwelliannau newydd

Rhif cyhoeddi	CAS-255025-Q1G0R5
Modelau yr effeithir arnynt	AFG1062
Gwellhad	Five new SCPI commands added. Details below.
Rhif cyhoeddi	CES2T-100
Modelau yr effeithir arnynt	AFG1062
Gwellhad	Upon firmware upgrade, acceptance of the End User License Agreement (EULA) on the front panel of the instrument is required before use.

[SOURce[1|2]]:BURSt:PERiod

This command sets or queries the burst period (trigger interval) in burst mode.

• Conditions: None
• Group: Source
• Syntax: [SOURce[1|2]]:BURSt:PERiod {<seconds> | MINimum | MAXimum}
  • [SOURce[1|2]]:BURSt:PERiod? {MINimum | MAXimum}
• Arguments: <seconds>::=<NRf>[<units>] where:
  • <NRf> is the burst period in seconds.
  • <units>::=[ns | μs | ms | s]
• Returns: <seconds>
• Example: SOURce1:BURSt:PERiod 100ms
  Sets the channel 1 burst period to 100 ms.

[SOURce[1|2]]:BURSt:PHASe

This command sets or queries the phase of the output waveform in burst mode for the specified channel. Set the value in radians or degrees. If no units are specified, the default is RAD. The query returns the value in RAD.

• Conditions: None
• Group: Source
• Syntax: [SOURce[1|2]]:BURSt:PHASe {<phase> | MINimum | MAXimum}
• [SOURce[1|2]]:BURSt:PHASe? {MINimum | MAXimum}
• Arguments: <phase>::=<NR3>[<units>]
  • lle:
  • <NR3> is the phase of the output waveform.
  • <units>::=[RAD | DEG]
  • If units are omitted, RAD is selected. The setting ranges are:
  • RAD: -2 Pl to +2 Pl, relative to phase value.
  • DEG: -360 to +360, relative to phase value.
• Returns: <phase>
• Example: SOURce1:BURSt:PHASe MAXimum

Sets the maximum value for the burst mode phase of the output waveform for CH 1.

[SOURce[1|2]]:BURSt:POLarity

This command sets or queries the trigger gate polarity in burst gated mode.

• Conditions: None
• Group: Source
• Syntax: [SOURce[1|2]]:BURSt:POLarity {POSitive|NEGative}
• [SOURce[1|2]]:BURSt:POLarity?
• Arguments: POSitive specifies a positive trigger gate polarity.
• NEGative specifies a negative trigger gate polarity.
• Returns: POS|NEG
• Example: [SOURce[1|2]]:BURSt:POLarity POSitive
• Sets the trigger gate polarity of CH 1 to positive.

SYSTem:CLKSrc

This command sets or queries the system’s clock source.

• Group: System
• Syntax: SYSTem:CLKSrc {INTernal|EXTernal}
• SYSTem:CLKSrc?
• Arguments: INTernal specifies the clock source as the internal clock signal.
• EXTernal specifies the clock source as an external clock signal.
• Returns: INT|EXT
• Example: SYSTem:CLKSrc INTernal
• Sets the system clock source to the internal clock.

TRIGger:SLOPe

This command sets or queries the slope edge the external trigger event occurs on.

• Group: Trigger
• Syntax: TRIGger:SLOPe {POSitive|NEGative}
• TRIGger:SLOPe?
• Arguments: POSitive specifies that the trigger event occurs on the rising edge of the externaltrigger signal.
• NEGative specifies that the trigger event occurs on the falling edge of the externaltrigger signal.
• Returns: POS|NEG,POS|NEG,POS|NEG,POS|NEG where the first and third return value is the external trigger slope of sweep mode for channel 1 and 2, and the second and fourth return value is the external trigger slope of burst mode for channel 1 and 2.
• Example: TRIGger:SLOPe POSitive Sets the trigger slope to positive, which triggers on the rising edge of the signal.

Datrys problemau

Rhif cyhoeddi	CAS-290934-H5T6R9
Modelau yr effeithir arnynt	AFG1062
Symptomau	Pulse waveform output in continuous mode goes to pulse high level for an extended time before going to 0 V when the output is turned off.
Datrysiad	Mae'r mater hwn wedi'i gywiro.
Rhif cyhoeddi	CAS-296793-Y7Y0W4
Modelau yr effeithir arnynt	AFG1062
Symptomau	Pulse waveform output incorrectly inverted when an offset other than 0 V was used.
Datrysiad	Mae'r mater hwn wedi'i gywiro.
Rhif cyhoeddi	CAS-333592-P5X5K9
Modelau yr effeithir arnynt	AFG1062
Symptomau	The [SOURce[1|2]]:PULSe:DCYCle command generates an error.
Datrysiad	Mae'r mater hwn wedi'i gywiro.
Rhif cyhoeddi	CAS-362740-R9L3J4
Modelau yr effeithir arnynt	AFG1062
Symptomau	Ref Clk/Counter could not synchronize to an external reference clock or counter input.
Datrysiad	Mae'r mater hwn wedi'i gywiro.
Rhif cyhoeddi	CAS-40294-GS62Q8
Modelau yr effeithir arnynt	AFG1062
Symptomau	When using pulse waveform in burst mode, changing the pulse period incorrectly changed the pulse width.
Datrysiad	Mae'r mater hwn wedi'i gywiro.

Problemau hysbys

Rhif cyhoeddi	CAS-215793-Z6H6W9
Modelau yr effeithir arnynt	AFG1062
Symptomau	Ref Clk Out cannot output an external reference clock or counter it receives through its Ref Clk/Counter input.
Gweithiwch o gwmpas	When synchronizing the clocks of more than two instruments, place the AFG as either the origin of the clock signal or the last instrument being synchronized.

Cyfarwyddiadau gosod

CAUTION. Updating your instrument firmware is a sensitive operation; it is critical that you follow the instructions below. If you do not, you may cause damage to your instrument. For exampLe, er mwyn atal difrod i'r offeryn, peidiwch â thynnu'r gyriant fflach USB ar unrhyw adeg wrth ddiweddaru'r firmware, a pheidiwch â phweru'r offeryn yn ystod y broses ddiweddaru.

I ddiweddaru firmware eich offeryn:

1. Visit tek.com and search for the AFG1062 firmware.
2. Dadlwythwch y .zip cywasgedig file i'ch cyfrifiadur.
3. Dadsipio'r llwytho i lawr file and copy the .tfb file i'r cyfeiriadur gwreiddiau gyriant fflach USB.
4. Insert the USB flash drive into the instrument front panel.
5. On the front panel, press the Utility button. The Utility menu is displayed.
6. From the instrument Utility menu, select System.
7. Press Next Page until the Update firmware option is displayed. This option will be disabled if you do not have a USB flash drive inserted or Access Protection is turned on.
8. Select Update firmware.
9. With the navigation wheel, select USBDEVICE, then select Enter.
10. With the navigation wheel, select the .tfb file, then select Execute.
11. Darllen file… will be displayed, followed by Updating file system… with a progress bar.
    CAUTION. Updating the firmware takes approximately two minutes. Do not remove the USB flash drive during the update process.
    If you accidentally remove the USB drive during the update, do not power off the instrument. Restart the upgrade process from the Utility menu.
12. When the upgrade is finished, the instrument will display “Firmware upgrade success!”
13. The instrument will automatically reboot.
14. When the instrument has rebooted, the instrument End-User License Agreement (EULA) is displayed.You must accept the EULA before you can use the instrument.
15. Remove the USB drive. You can verify that the firmware has been updated by going to the Utility menuand viewing the version.

Firmware downgrades
If your instrument does not function properly after a firmware upgrade, you can downgrade by following the steps under Installation instructions with an earlier version of the firmware file. However, please note the following conditions before attempting a downgrade.

• If your instrument serial number is 2231001 or higher, you can only downgrade to Version 1.1.0 ornewer
• If your instrument serial number is 2231000 or lower, you can only downgrade to Version 1.1.0 ornewer once the instrument is upgraded to Version 1.1.0 or newer

If you attempt a downgrade and it is not successful due to the specified conditions, you will receive an error.

Atodiad A - Fersiynau blaenorol

FERSIWN 1.1.0
This release does not include any critical fixes or enhancements.

FERSIWN 1.0.9

Datrys problemau

Rhif cyhoeddi	AR-62341
Modelau yr effeithir arnynt	AFG1062
Symptomau	Pulse duty cycle stuck at 50% in burst mode, even when user attempts to change it.
Datrysiad	Mae'r mater hwn wedi'i gywiro.
Rhif cyhoeddi	AR-62464
Modelau yr effeithir arnynt	AFG1062
Symptomau	Cycle counts larger than 65000 in burst mode is incorrect.
Datrysiad	Mae'r mater hwn wedi'i gywiro.

FERSIWN 1.0.6
Datrys problemau

Rhif cyhoeddi	Ddim yn berthnasol
Modelau yr effeithir arnynt	AFG1062
Symptomau	Output signal requires optimization when trigger source is manual or external in burst mode.
Datrysiad	Mae'r mater hwn wedi'i gywiro.

FERSIWN 1.0.5
Datrys problemau

Rhif cyhoeddi	Ddim yn berthnasol
Modelau yr effeithir arnynt	AFG1062
Symptomau	The arbitrary waveform does not output in burst mode.
Datrysiad	Mae'r mater hwn wedi'i gywiro.
Rhif cyhoeddi	Ddim yn berthnasol
Modelau yr effeithir arnynt	AFG1062
Symptomau	Phase align malfunctions in burst mode.
Datrysiad	Mae'r mater hwn wedi'i gywiro.
Rhif cyhoeddi	Ddim yn berthnasol
Modelau yr effeithir arnynt	AFG1062
Symptomau	DC offset is inconsistent with over waveforms.
Datrysiad	Mae'r mater hwn wedi'i gywiro.
Rhif cyhoeddi	Ddim yn berthnasol
Modelau yr effeithir arnynt	AFG1062
Symptomau	The HFR malfunctions.
Datrysiad	Mae'r mater hwn wedi'i gywiro.
Rhif cyhoeddi	Ddim yn berthnasol
Modelau yr effeithir arnynt	AFG1062
Symptomau	Abnormal arbitrary waveform output under certain conditions.
Datrysiad	Mae'r mater hwn wedi'i gywiro.
Rhif cyhoeddi	Ddim yn berthnasol
Modelau yr effeithir arnynt	AFG1062
Symptomau	Thumbnail does not update when changes to the settings are made.
Datrysiad	Mae'r mater hwn wedi'i gywiro.

FERSIWN 1.0.4
Datrys problemau

Rhif cyhoeddi	Ddim yn berthnasol
Modelau yr effeithir arnynt	AFG1062
Symptomau	The [SOURce[1|2]]:PHASe[:ADJust] command does not work in burst mode.
Datrysiad	Mae'r mater hwn wedi'i gywiro.
Rhif cyhoeddi	Ddim yn berthnasol
Modelau yr effeithir arnynt	AFG1062
Symptomau	The trigger level is not correct in sweep mode.
Datrysiad	Mae'r mater hwn wedi'i gywiro.
Rhif cyhoeddi	Ddim yn berthnasol
Modelau yr effeithir arnynt	AFG1062
Symptomau	The arbitrary waveform quality requires optimization.
Datrysiad	Mae'r mater hwn wedi'i gywiro.
Rhif cyhoeddi	Ddim yn berthnasol
Modelau yr effeithir arnynt	AFG1062
Symptomau	The counter function requires optimization.
Datrysiad	Mae'r mater hwn wedi'i gywiro.
Rhif cyhoeddi	Ddim yn berthnasol
Modelau yr effeithir arnynt	AFG1062
Symptomau	More PI commands require support.
Datrysiad	Mae'r mater hwn wedi'i gywiro.

FERSIWN 1.0.3
Nodweddion / gwelliannau newydd

Rhif cyhoeddi	Ddim yn berthnasol
Modelau yr effeithir arnynt	AFG1062
Symptomau	Added support for the DATA:DATA? EMEM command.
Datrysiad	Mae'r mater hwn wedi'i gywiro.

FERSIWN 1.0.2
Nodweddion / gwelliannau newydd

Rhif cyhoeddi	Ddim yn berthnasol
Modelau yr effeithir arnynt	AFG1062
Symptomau	Align phase function upgraded.
Datrysiad	Mae'r mater hwn wedi'i gywiro.
Rhif cyhoeddi	Ddim yn berthnasol
Modelau yr effeithir arnynt	AFG1062
Symptomau	User settings can be saved to the instrument (.tfs format).
Datrysiad	Mae'r mater hwn wedi'i gywiro.
Rhif cyhoeddi	Ddim yn berthnasol
Modelau yr effeithir arnynt	AFG1062
Symptomau	User waveforms can be moved from a USB drive to the instrument (.tfw format).
Datrysiad	Mae'r mater hwn wedi'i gywiro.
Rhif cyhoeddi	Ddim yn berthnasol
Modelau yr effeithir arnynt	AFG1062
Symptomau	BRASTER16 file system has been upgraded to support USB drives.
Datrysiad	Mae'r mater hwn wedi'i gywiro.
Rhif cyhoeddi	Ddim yn berthnasol
Modelau yr effeithir arnynt	AFG1062
Symptomau	Additional SCPI commands added.
Datrysiad	Mae'r mater hwn wedi'i gywiro.

Cwestiynau Cyffredin

Q: How can I update the firmware of AFG1062?

A: To update the firmware, follow the installation instructions provided in the user manual for Version 1.2.0.

Q: What should I do if I encounter a known problem with the software?

A: If you encounter a known problem, refer to the problem fixes section in the release notes for possible workarounds.

Dogfennau / Adnoddau

Generadur Swyddogaeth Gyflafaidd Tektronix AFG1062 [pdfCanllaw Gosod AFG1062 Arbitrary Function Generator, AFG1062, Arbitrary Function Generator, Function Generator, Generator

Cyfeiriadau

• Llawlyfr Defnyddiwr