Synapse CSEN1 Combo Sensor Controller Installation Guide

CANLLAW INSTALL
CSEN1

CSEN1 Combo Sensor Controller

Part Numbers: CSEN1-H-W-ZHA (white enclosure) and CSEN1-H-G-ZHA (gray enclosure)

DISGRIFIAD

The CSEN1 is a low voltage Networked Lighting Controller with an integrated passive infrared sensor and a photocell. It is powered via the AUX power from the LED driver. The CSEN1 autodetects both 0-10V Drivers and D4i Drivers to simplify the installation. The product is DLC certified for both indoor and outdoor applications.

MANYLION

• Amlder Radio: 2.4 GHz (IEEE 802.15.4)
• Pŵer Allbwn Trosglwyddo RF: +20dBM
• Tymheredd Gweithredu: -40 ° i +70 ° C
• Lleithder Gweithredu: 10 i 95%, heb fod yn gyddwyso
• Cau Tir â Gradd IP66
• Dimensiynau: 3.1” D x 1.6” H (80mm D x 42mm H)
• Input Power: 12-24VDC, 35mA max, 840mW
• Pwrpas rheolaeth: Gweithredu
• Environmental: Indoor/Outdoor
• Gradd Llygredd: 3
• Graddedig Impulse Voltage:330V

YSTYRIAETHAU DYLUNIO

Below are some recommendations for successful analog dimming using the CSEN1. The analog dimming control wires are referenced as DALI+/DIM+ and Common Ground/DALI-. The dimming signals have a Maximum voltage o 10V DC.

• Do not ground the Common Ground/DALI- wire to chassis ground; this is a return signal and is critical for proper dimming.
• Llwybr gwifrau pylu oddi wrth linellau AC os yn bosibl.
• Uchafswm o 4 Gyrwyr LED DALI-2/D4i fesul rheolydd, ymgynghorwch â Synapse Support os oes angen cymhareb uwch.
• Maximum of 8 DIM to OFF LED Drivers for DIM to OFF Designs.
• Peidiwch â gosod ar heatsink neu i yrrwr LED.

NODYN: Rhaid i Gyrrwr LED gefnogi ymarferoldeb DIM i OFF.
RHYBUDDION A RHYBUDDION

• TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
• The CSEN1 should only be installed in a fixture with a Zhaga Book 18 receptacle.
• Gallai methu â dilyn y cyfarwyddiadau a'r rhybuddion hyn ddirymu'r warant.
• This product must be installed in accordance with national, state, and local electrical codes and requirements.
• If you are unsure about any part of these instructions, consult an electrician; qualified personnel should perform all work.

MANYLION Gwifro LLYFR ZHAGA 18 SOced

TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!
For fixtures with an existing Zhaga socket, prior to installation, verify the wiring per the details below. (See Figure 1) If the fixture does not have a Zhaga socket, use the appropriate Wired Adapter accessory based on the knockout size: CSEN1-ZHA-ADPT-22 for 22mm knockouts, or CSEN1-ZHA-ADPT-33 for 33mm knockouts. The specifications for the signal wires are:

• 12-24VDC POWER: Brown
• Common Ground/DALI-: Pink with White Stripe
• DALI+/DIM+: Violet with White Stripe
• Solid Conductor, 105°C, Rated for 600VAC, AWG 20, 15” Length

FFIGUR 1

CYFARWYDDIADAU GOSOD

TURN OFF POWER AT CIRCUIT BREAKER OR FUSE AND TEST THAT POWER IS OFF BEFORE INSTALLING OR SERVICING!

1. Os yw'n berthnasol, tynnwch y cap selio neu'r ddyfais rheoli goleuadau sydd wedi'i osod ar hyn o bryd yn y cynhwysydd gosodion.
2. Align the CSEN1 such that the contacts pins are positioned at the appropriate the receptacle contacts.
3. After alignment, push until the CSEN1 is fully seated within the receptacle.
4. While pushing against the device, twist the CSEN1 housing clockwise until it locks into place. The CSEN1 includes a latching key or notch that will lock into position with an audible “click”. (See Figure 2)

Nodyn: I weithio'n iawn, gwnewch yn siŵr bod y rheolydd yn cael ei fewnosod yn gyfan gwbl yn y soced a'i droelli i'r safle dan glo.
Rhybudd: The Zhaga receptacle should not turn during installation. Turning the receptacle could damage the internal fixture wiring by pulling it loose.
FFIGUR 2

LEDS STATUS

GWYBODAETH RHEOLEIDDIOL A TYSTYSGRIFAU
RF Exposure Statement: This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance of 20cm between the radiator and your body. This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
Tystysgrifau Industry Canada (IC): Nid yw'r cyfarpar digidol hwn yn fwy na'r terfynau Dosbarth B ar gyfer allyriadau sŵn radio o gyfarpar digidol a nodir yn Rheoliadau Ymyrraeth Radio Adran Gyfathrebu Canada.
Tystysgrifau Cyngor Sir y Fflint a gwybodaeth reoleiddiol (UDA yn unig)
Cyngor Sir y Fflint Rhan 15 Dosbarth B: Mae'r ddyfais hon yn cydymffurfio â rhan 15 o reolau Cyngor Sir y Fflint. Mae gweithrediad yn ddarostyngedig i'r ddau amod a ganlyn: (1) Efallai na fydd y dyfeisiau hyn yn achosi ymyrraeth niweidiol, a (2) Rhaid i'r dyfeisiau hyn dderbyn unrhyw ymyrraeth a dderbynnir, gan gynnwys ymyrraeth a allai achosi gweithrediad niweidiol.
RADIO FREQUENCY INTERFERENCE (RFI) (FCC 15.105): This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: (1) Re-orient or relocate the receiving antenna; (2) Increase the separation between the equipment and the receiver; (3) Connect the equipment into an outlet on a circuit different from that to which the receiver is connected; (4) Consult the dealer or an experienced radio/TV technician for help.
Declaration of Conformity (FCC 96-208 & 95-19): Synapse Wireless, Inc. declares that the product name CSEN1 to which this declaration relates, meet the requirements specified by the Federal Communications Commission as detailed in the following specifications:

• Rhan 15, Is-ran B, ar gyfer offer Dosbarth B
• Cyngor Sir y Fflint 96-208 fel y mae'n berthnasol i gyfrifiaduron personol a pherifferolion Dosbarth B
• Mae'r cynnyrch hwn wedi'i brofi mewn Labordy Prawf Allanol a ardystiwyd yn unol â rheolau Cyngor Sir y Fflint a chanfuwyd ei fod yn cwrdd â Therfynau Allyriadau Rhan 15 yr FCC. Mae'r ddogfennaeth ymlaen file ac ar gael gan Synapse Wireless, Inc.

Os nad yw'r ID Cyngor Sir y Fflint ar gyfer y modiwl y tu mewn i'r amgaead cynnyrch hwn yn weladwy pan gaiff ei osod y tu mewn i ddyfais arall, yna rhaid i'r tu allan i'r ddyfais y mae'r cynnyrch hwn wedi'i osod ynddi hefyd arddangos label sy'n cyfeirio at y modiwl amgaeedig ID FCC. Addasiadau (CSFf 15.21):
Gall newidiadau neu addasiadau i'r offer hwn nad ydynt wedi'u cymeradwyo'n benodol gan Synapse Wireless, Inc., ddirymu awdurdod y defnyddiwr i weithredu'r offer hwn.
Patent – ​​marcio rhithwir yn https://www.synapsewireless.com/about/patents
I ddysgu mwy ewch i: synapsewireless.com

TYSTYSGRIFAU

DALI-2 Rheolwr Cais Ardystiedig