Canllawiau Gweithredu M5StickC Plus2
Firmware Ffatri
Pan fydd y ddyfais yn dod ar draws problemau gweithredol, gallwch geisio ail-fflachio'r cadarnwedd ffatri i wirio a oes unrhyw gamweithrediad caledwedd. Cyfeiriwch at y tiwtorial canlynol. Defnyddiwch yr offeryn fflachio cadarnwedd M5Burner i fflachio'r cadarnwedd ffatri ar y ddyfais.
FAQ
C1: Pam mae sgrin ddu ar fy M5StickC Plus2/na fydd yn cychwyn?
Atebion: M5Burner Burn official Factory Firmware“M5StickCPlus2 User Demo”
C2: Pam mai dim ond 3 awr yw'r amser gweithio? Pam mae'n codi tâl 100% mewn 1 munud, tynnwch y cebl codi tâl a bydd yn diffodd?
Solutions: “Bruce for Stack plus2”This is an unofficial firmware. Flashing unofficial firmware can void your warranty, cause instability, and expose your device to security risks. Proceed with caution.
Llosgwch y cadarnwedd swyddogol yn ôl.
Paratoi
- Cyfeiriwch at y tiwtorial M5Burner i gwblhau'r lawrlwythiad o'r offeryn fflachio cadarnwedd, ac yna cyfeiriwch at y ddelwedd isod i lawrlwytho'r cadarnwedd cyfatebol.
Dolen llwytho i lawr: https://docs.m5stack.com/en/uiflow/m5burner/intro
Gosod Gyrrwr USB
Awgrym Gosod Gyrrwr
Cliciwch y ddolen isod i lawrlwytho'r gyrrwr sy'n cyfateb i'ch system weithredu. Gellir lawrlwytho a gosod y pecyn gyrrwr ar gyfer y CP34X (ar gyfer y fersiwn CH9102) trwy ddewis y pecyn gosod sy'n cyfateb i'ch system weithredu. Os byddwch chi'n dod ar draws problemau gyda lawrlwytho rhaglenni (megis terfyn amser neu wallau "Methodd ysgrifennu i'r RAM targed"), ceisiwch ailosod y gyrrwr dyfais.
CH9102_VCP_SER_Windows
https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/drivers/CH9102_VCP_SER_Windows.exe
CH9102_VCP_SER_MacOS fersiwn 1.7
https://m5stack.oss-cn-shenzhen.aliyuncs.com/resource/drivers/CH9102_VCP_MacOS_v1.7.zip
Dewis Porthladd ar MacOS
Ar MacOS, efallai y bydd dau borthladd ar gael. Wrth eu defnyddio, dewiswch y porthladd o'r enw wchmodem.
Dewis Porthladdoedd
Cysylltwch y ddyfais â'r cyfrifiadur drwy gebl USB. Ar ôl i'r gosodiad gyrrwr gael ei gwblhau, gallwch ddewis y porthladd dyfais cyfatebol yn M5Burner.
Llosgi
Cliciwch “Llosgi” i gychwyn y broses fflachio.
StickC-Plus2
SKU:K016-P2
Disgrifiad
StickC-Plus2 is the iterative version of Stick C-Plus. It is powered by the ESP32-PICO-V3-02 chip, providing Wi-Fi connectivity. Within its compact body, it integrates a rich variety of hardware resources, including IR emitter, RTC, microphone, LED, IMU, buttons, buzzer, and more. It features a 1.14-inch TFT display driven by the ST7789V2 with a resolution of 135 x 240.
The battery capacity has been increased to 200 mAh, and the interface is compatible with both HAT and Unit series modules.
This sleek and compact development tool can ignite unlimited creativity. StickC-Plus2 helps you quickly build IoT product prototypes and greatly simplifies the entire development process. Even beginners who are new to programming can create interesting applications and apply them in real life.
Tiwtorial
UIFlow
This tutorial will introduce how to control the StickC-Plus2 device through the UIFlow graphical programming platform.
UiFlow2
This tutorial will introduce how to control the StickC-Plus2 device through the UiFlow2 graphical programming platform.
IDE Arduino
This tutorial will introduce how to program and control the StickC-Plus2 device using the Arduino IDE.
Nodyn
Port Not Recognized
When using a C-to-C cable, if the port cannot be recognized, please perform the following power-on procedure:
disconnect StickC-Plus2, power it off (long-press the power button until the green LED lights up), then reconnect the USB cable to power on.
Nodweddion
- Based on ESP32-PICO-V3-02 with Wi-Fi support
- Built-in 3-axis accelerometer and 3-axis gyroscope
- Integrated IR emitter
- Built-in RTC
- Meicroffon integredig
- User buttons, 1.14-inch LCD, power/reset button
- Batri Li-ion 200 mAh
- Cysylltydd ehangu
- Integrated passive buzzer
- Wearable & mountable
- Llwyfan Datblygu
- UiFlow1
- UiFlow2
- IDE Arduino
- ESP-IDF
- LlwyfanIO
Yn cynnwys
- 1 x StickC-Plus2
Ceisiadau
- Dyfeisiau gwisgadwy
- IoT controller
- STEM education
- prosiectau DIY
- Dyfeisiau cartref clyfar
Manylebau
| Manyleb | Paramedr |
| SoC | ESP32-PICO-V3-02 240 MHz dual-core, Wi-Fi, 2 MB PSRAM, 8 MB Flash |
| Mewnbwn Voltage | 5 V @ 500 mA |
| Rhyngwyneb | Type-C x 1, GROVE (I2C + I/O + UART) x 1 |
| Sgrin LCD | 1.14 inch, 135 x 240 Color TFT LCD, ST7789V2 |
| Meicroffon | SPM1423 |
| Botymau | User buttons x 3 |
| LED | Green LED x 1 (non-programmable, sleep indicator) Red LED x 1 (shares control pin G19 with IR emitter) |
| RTC | BM8563 |
| Swniwr | On-board passive buzzer |
| IMU | MPU6886 |
| Antena | 2.4 G 3D antenna |
| Pinnau Allanol | G0, G25/G26, G36, G32, G33 |
| Batri | 200 mAh @ 3.7 V, inside |
| Gweithredu Dros Dro | 0 ~ 40 ° C |
| Amgaead | Plastig (PC) |
| Maint Cynnyrch | 48.0 x 24.0 x 13.5mm |
| Pwysau Cynnyrch | 16.7 g |
| Maint Pecyn | 104.4 x 65.0 x 18.0mm |
| Pwysau Crynswth | 26.3 g |
Cyfarwyddiadau Gweithredu
Pŵer Ymlaen / Diffodd
Power-on: Press the “BUTTON C” for more than 2 seconds, or wake up via the RTC IRQ signal. After the wake-up signal is triggered, the program must set the HOLD pin (G4) to high (1) to keep the power on, otherwise the device will shut down again.
Power-off: Without external USB power, press “BUTTON C” for more than 6 seconds, or set HOLD (GPIO4)=0 in the program to power off. While USB is connected, pressing “BUTTON C” for more than 6 seconds will turn off the screen and enter sleep mode (not a full power-off).
Sgemateg
Map Pin
Red LED & IR Emitter | Button A | Button B | Buzzer
| ESP32-PICO-V3-02 | GPIO19 | GPIO37 | GPIO39 | GPIO35 | GPIO2 |
| IR Emitter & Red LED | IR emitter & Red LED pin | ||||
| Botwm A | Botwm A | ||||
| Botwm B | Botwm B | ||||
| Botwm C | Botwm C | ||||
| Bwncath Goddefol | Swniwr |
Arddangosfa TFT Lliw
Driver IC: ST7789V2
Cydraniad: 135 x 240
| ESP32-PICO-V3-02 | G15 | G13 | G14 | G12 | G5 | G27 |
| Arddangosfa TFT | TFT_MOSI | TFT_CLK | TFT_DC | TFT_RST | TFT_CS | TFT_BL |
Microphone MIC (SPM1423)
| ESP32-PICO-V3-02 | G0 | G34 |
| MIC SPM1423 | CLK | DATA |
6-Axis IMU (MPU6886) & RTC BM8563
| ESP32-PICO-V3-02 | G22 | G21 | G19 |
| IMU MPU6886 | SCL | SDA | |
| BM8563 | SCL | SDA | |
| Allyrrydd IR | TX | ||
| LED coch | TX |
HY2.0-4P
| HY2.0-4P | Du | Coch | Melyn | Gwyn |
| PORT.CUSTOM | GND | 5V | G32 | G33 |
Maint Model
Taflenni data
ESP32-PICO-V3-02
ST7789V2
BM8563
MPU6886
SPM1423
Meddalwedd
Arduino
StickC-Plus2 Arduino Quick Start
StickC-Plus2 Library
StickC-Plus2 Factory Test Firmware
UiFlow1
StickC-Plus2 UiFlow1 Quick Start
UiFlow2
StickC-Plus2 UiFlow2 Quick Start
LlwyfanIO
[env:m5stack-stickc-plus2]
platform = espressif32@6.7.0
board = m5stick-c
fframwaith = arduino
upload_speed = 1500000
monitor_speed = 115200
build_flags =
-DBOARD_HAS_PSRAM
-mfix-esp32-psram-cache-issue
-DCORE_DEBUG_LEVEL=5
lib_deps =
M5Unified=https://github.com/m5stack/M5Unified
Gyrrwr USB
Click the links below to download the driver that matches your operating system. The package contains CP34X drivers (for CH9102). After extracting the archive, run the installer that matches your OS bit-depth.
If you encounter issues such as timeout or “Failed to write to target RAM” during downloading, please try reinstalling the driver.
| Enw Gyrrwr | Supported Chip | Lawrlwythwch |
| CH9102_VCP_SER_Windows | CH9102 | Lawrlwythwch |
| CH9102_VCP_SER_MacOS fersiwn 1.7 | CH9102 | Lawrlwythwch |
macOS Port Selection
Two serial ports may appear on macOS. Please select the port named wchmodem.
Easy loader
Easy Loader is a lightweight program flasher that comes with a demonstration firmware. By following a few simple steps, you can flash it to the controller for quick functional verification.
| Easy loader | Lawrlwythwch | Nodyn |
| Factory Test for Windows | llwytho i lawr | / |
Arall
StickC-Plus2 Restore Factory Firmware Guide
Fideo
StickC-Plus2 Feature Introduction
StackC Plus2 视频.mp4
Newid Fersiwn
| Dyddiad Rhyddhau | Newid Disgrifiad | Nodyn |
| / | Rhyddhad cyntaf | / |
| 2021-12 | Added sleep and wake-up function, version updated to v1.1 | / |
| 2023-12 | Removed PMIC AXP192, MCU changed from ESP32-PICO-D4 to ESP32-PICO-V3-02, different power-on/off method, version v2 | / |
Cymhariaeth Cynnyrch
Gwahaniaethau Caledwedd
| Cynnyrch Enw |
SoC | Rheoli Pŵer | Gallu Batri | Cof | USB-UART Chip | Lliw |
| Stick C-Plus | ESP32-PICO-D4 | AXP192 | 120 mAh | 520 KB SRAM + 4 MB Flash | CH522 | Red- orange |
| StickC-Plus2 | ESP32-PICO-V3-02 | / | 200 mAh | 2 MB PSRAM + 8 MB Flash | CH9102 | Oren |
Pin Differences
| Enw Cynnyrch | IR | LED | TFT | BUTTON A. | BUTTON B. | BOTWM C (WAKE) |
DALWCH | Batri Cyftage Canfod |
| M5STICKC PLUS | G9 | G10 | MOSI (G15) CLK (G13) DC (G23) RST (G18) CS (G5) |
G37 | G39 | Rheolaidd botwm |
/ | Via AXP192 |
| M5STICKC PLUS2 | G19 | G19 | MOSI (G15) CLK (G13) DC (G14) RST (G12) CS (G5) |
G37 | G39 | G35 | G4 | G38 |
Power On/Off Differences
| Cynnyrch Enw | Pŵer Ymlaen | Pŵer i ffwrdd |
| Stick C- Plus2 | Press “BUTTON C” for more than 2 s, or wake via RTC IRQ. After wake-up, set HOLD (G4)=1 in the program to keep power on, otherwise the device will shut down again. |
Without USB power, press “BUTTON C” for more than 6 s, or set HOLD (GPIO4)=0 in the program to power off. With USB connected, pressing “BUTTON C” for more than 6 s will turn off the screen and enter sleep, but not a full power- off. |
Because StickC-Plus2 removes the PMIC AXP192, the power-on/off method differs from previous versions. As mentioned at the beginning of this document, the operation is largely similar, but the supported libraries will differ. Wi-Fi and IR signal strength have both been improved compared to the previous model.
Dogfennau / Adnoddau
 |
M5STACK ESP32-PICO-V3-02 IoT Development Module [pdfCanllaw Defnyddiwr ESP32-PICO-V3-02 IoT Development Module, ESP32-PICO-V3-02, IoT Development Module, Development Module, Module |