GLEDOPTO GL-C-301P ZigBee Pro Plus 5 In 1 LED Smart Controller
LLAWLYFR CYFARWYDDYD
MODEL: GL-C-301P
Paramedr Cynnyrch
- Product Model: GL-C-301P
- Mewnbwn Voltage: DC 12-24V
- Allbwn Cyfredol/Sianel: 6A Uchafswm
- Cyfanswm Allbwn Cyfredol: 10A Uchafswm
- Communication Protocol: ZigBee 3.0 + 2.4G RF
- Math Gwifren a Awgrymir: 0.5-1.5mm² (24-16AWG)
- Hyd Stripio: 8-9mm
- Deunydd: PC gwrth-dân
- Cyfradd IP: IP20
- Tymheredd Gweithredu: -20 ~ 45 ℃
- Maint: 42x38x17mm
OPT:
Short Press: Switch current device function (switching device function will automatically clear Zigbee and RF connections)
Long Press for 5 seconds: Enable/disable memory function (memory function is off by default, it determines whether to remember the power status before power off)
Ail gychwyn:
Short Press: Switch the frequency.
Long Press for 5 seconds: Reset the controller. (After reset, it default back to RGBCCT).
Gwthio:
Pwyswch yn fyr: Pŵer ymlaen/i ffwrdd.
Pwyswch yn hir: Addasu disgleirdeb (Gan dybio: Mae pwyswch yn hir yn cynyddu disgleirdeb, rhyddhewch a phwyswch yn hir eto yn lleihau disgleirdeb).
Gosodiadau Amlder
Er mwyn bod yn berthnasol i wahanol gyflenwadau pŵer, gellir dewis amledd y ddyfais fel 600Hz, 800Hz, 1000Hz, 2000Hz, 4000Hz, 8000Hz gyda'r amledd diofyn o 1000Hz. Pwyswch yr allwedd "Gosod" ddwywaith yn fyr, bydd yr amledd yn newid i'r un nesaf. Bydd y dangosydd yn fflachio mewn lliw pinc ac yn ailddechrau i'r lliw blaenorol ar ôl "diffodd" am 2 eiliad. Cyfeiriwch at y tabl ar gyfer rheol amseroedd fflachio'r dangosydd ar gyfer gwahanol amledd.
Dangosydd Statws Golau
Diagram Gwifrau
RGBCCT:
Under RGBCCT function, the RGBCCT strip can be connected to the device
RGBW:
O dan swyddogaeth RGBW, gellir cysylltu'r stribed RGBW, heb unrhyw gysylltiad â therfynell “N”.
RGB:
O dan swyddogaeth RGB, gellir cysylltu'r stribed RGB, heb unrhyw gysylltiad â therfynell “N”.
CCT:
O dan swyddogaeth CCT, gellir cysylltu dau ddarn o stribedi CCT, heb unrhyw gysylltiad â therfynell "N", ond bydd y stribedi golau yn cael eu rheoli ar yr un pryd.
DIMMER:
Under dimmer function, five pieces of single color strips can be connected, but the light strips will be controlled simultaneously
Connecting with the Gateway
Joining Network:
1. Connect the controller to power correctly.
2. Use the gateway’s app to start device search, wait for a certain period (refer to the instructions of each gateway). If the gateway does not find the controller, try powering the controller again or resetting it.
3. After the gateway discovers the controller, add the controller to the designated room or group.
4. Once joined to the network, you can start using the controller
Leaving Network:
In the app, delete the controller that needs to leave the network. The controller will flash 3 times, indicating successful disconnection.
Nodyn: Disconnection of the controller will clear the 2.4G RF connection and enter the reset state.
The product works with many ZigBee 3.0 Gatewayslike Philips Hue, Amazon ECho Plus or Smart Things.
Paru/Dadbaru Rheolydd o Bell
Paru:
- Diffoddwch y rheolydd, yna trowch ef ymlaen ar ôl 10 eiliad.
- O fewn 4 eiliad i droi’r pŵer ymlaen, pwyswch y botwm “Ymlaen” ar unrhyw grŵp ar y teclyn rheoli o bell RF (gweler llawlyfr defnyddiwr pob teclyn rheoli o bell am fanylion).
- Pan fydd y stribed golau sydd wedi'i gysylltu â'r rheolydd yn fflachio, mae'n dangos bod y cysylltiad â'r teclyn rheoli o bell wedi llwyddo.
Anobeithiol:
- Diffoddwch y rheolydd, yna trowch ef ymlaen ar ôl 10 eiliad.
- Within 4 seconds of powering on, press the “Master On” button on the RF remote control or press the “On” button of the controller’s group 5 times.
- Pan fydd y stribed golau sy'n gysylltiedig â'r rheolydd yn fflachio, mae'n dynodi datgysylltiad o'r teclyn rheoli o bell.
2.4GHz Remote Control Scene Memory Function:
- Click on the button(S1,S2,S3,S4)of the remote control to enter the scene menory function.
- Long press to save the scene; Short press to activate the scene.
Yn gydnaws â Rheolydd Anghysbell RF 2.4G
Disgrifiad Modd
1. Static Warm white
2. Static Day white color
3. Static Cold white
4. Static Red color
5. Static Green color
6. Static Blue color
7. 16 Million Color Gradient
8. RGB Color Jumping
9. Color Breathing (Brightness gradually changes from 100% to 0%, then back to 100% to 0% in sequence. Adjusting color or color temperature can switch colors in this mode, press the “M” key to exit this mode).
Yn gydnaws â Rheolydd Anghysbell RF 2.4G
This controller can adjust the saturation using the remote control buttons.
Dull Ailosod
1. Button reset: Press and hold the RESET button for more than 5 seconds, the light strip flashes 3 times, indicating the reset is complete.
2. Power On/Off reset:
1. Power on the light strip controller.
2. Within 2 seconds, disconnect the power.
3. Wait for at least 5 seconds to ensure complete power-off.
4. Repeat the above steps 5 times.
5. The light strip will flash 3 times, indicating that the reset is complete.
Nodyn: The controller will return to RGBCCT function and clear Zigbee and RF connections after reseting.
1. Bafore turning on the power, please ensure that all wiring is correct and secure. Do not operate while the power is on.
2. Use the product under the rated voltage, Overvoltage neu undervoltage may damage controller.
3. Do not disassemble the product, as it may cause fire and electric shock.
4. Do not use the product in direct sunlight, damp, tymheredd uchel, neu amgylcheddau llym eraill.
5. Do not use the product in metal shielded areas or near strong magnetic fields, as it will severely affect the wireless sianaltransmission of the product.
YMADAWIADAU
- Due to our continuous adopfion of new technologies, the product specifications may change without prior notice.
- This manual is for reference and guidance purposes only. t does not guarantee complete consistency with the actual product. Please refer to theactual product for practical applications.
- The components and accessorles described in this manual do not represent the standard configuratlon of the product, The specific configurationis subject to the package contents.
- All text, tables, and images in this manual are protected by relevant naional laws and may not be used without our company’s permission.
- This product is compatible with thirdpary products (such as apps, hubs, etc,) as stated in the gateway compatibility chart. However, ourcompany takes no responsiblty for any issues that may arise from changes made by third-paty products, resulting in incompatibility orthe partial loss of functionality
LED-Fasnachu Tobias Ebert
Schoenicher Str. 42, Schoeneiche b.
Berlin, yr Almaen, 15566
0049 30 641 68917
info@led-trading.de
Manylebau:
- Dimensiynau: 17mm x 42mm x 38mm
- Frequency Options: 600Hz, 800Hz, 1000Hz, 2000Hz, 4000Hz, 8000Hz (default: 1000Hz)
Cwestiynau Cyffredin
Sut ydw i'n ailosod y rheolydd?
To reset the controller, long press the Reset button for 5 seconds. After reset, it defaults back to RGBCCT function.
Which gateways are compatible with the product?
The product works with ZigBee 3.0 Gateways like Philips Hue, Amazon Echo Plus, or SmartThings.
Dogfennau / Adnoddau
 |
GLEDOPTO GL-C-301P ZigBee Pro Plus 5 In 1 LED Smart Controller [pdfCyfarwyddiadau GL-C-301P, GL-C-301P ZigBee Pro Plus 5 In 1 LED Smart Controller, ZigBee Pro Plus 5 In 1 LED Smart Controller, 5 In 1 LED Smart Controller, LED Smart Controller, Smart Controller |
