Bwrdd Datblygu Super Mini Digilog ESP32

Manylebau

• Enw Cynnyrch: Bwrdd Datblygu Super Mini ESP32
• Math o Fwrdd: Modiwl Datblygu ESP32C3
• Cyfathrebu: USB CDC
• Cyfradd Baud: 9600
• LED Ar y Bwrdd: GPIO8

Gosod-1

My ESP32 Super Mini Dev Board (Fig. 1) accepts sketches from a PC, but it does not communicate with the Serial Monitor (Bd = 9600) though the onBoard LED (at GPIO8) blinks.
[image|403×203](upload://pRi2u3tDsAxTivzokiEplEtzhlC.jpeg)
Ffigur-1

Gosod-1

• Board: “ESP32C3 Dev Module”
• USB CDC on Boot: “Enabled”
• Port: “COM13 (ESP32S3 Dev Module)” //no other option

Braslun

• define LED_BUILTIN 8
• char myData[10];
• gosodiad gwagle()
• cyfres.begin(9600);
• pinMode(LED_BUILTIN, OUTPUT)
• dolen wag ()
• digitalWrite(LED_BUILTIN, HIGH); // trowch y LED ymlaen (HIGH yw'r cyfainttage lefel)
• delay(1000); // wait for a second
• digitalWrite(LED_BUILTIN, LOW); // diffoddwch yr LED drwy wneud y gyfroltage LOW delay(1000)
• beit n = Serial.ar gael();
• if (n != 0) { byte m = Serial.readBytesUntil(‘\n’, myData, sizeof (myData)-1); myData[m] = ‘\0’
• Serial.println(myData); }
• Serial.println(“Hello”); }

The following setup has solved the problem.

Gosod-2

• Board: “LOLIN C3 Mini”
• USB CDC on Boot: “Enabled”
• Port: “COM13 (ESP32S3 Dev Module)”
• Bd = 9600

Allbwn

• Helo
• Helo
• Arduino //From InputBox of SM to ESP32C3 to OutputBox of SM
• Helo
• Helo

Would be glad to hear your opinion as to — “what is LOLIN C3”.

1. Do not place the ESP32C3 Super Mini Board on the Breadboard to avoid contact problems.
2. Mae'r LED ar y bwrdd wedi'i gysylltu yn DPin-8.
3. Use a male-female jumper and connect the female side at DPin-9 to act as an external switch/button.
4. The connection diagram of the onFig. 1 LED and a button are similar to Fig. 1.
5. Select Board as follows: IDE 2.3.1 –> Tools –> ESP32.
6.  LOLIN C3 Mini USB CDC On Boot: Enabled.
7. Llwythwch y braslun a ddarperir i'r bwrdd.
8. Gwiriwch fod y LED ar y bwrdd i ffwrdd i ddechrau.
9. Closing the switch will make the onboard LED start blinking at a 2-second interval.
10. Ensure that the onboard LED is on.f
11. Gently touch the male side of the hanging wire/jumper with h G-pin of the Mini Board.
12. Confirm that the onboard LED is blinking at a 2-second interval.
13. Press the RST (Reset) Button of the Mini Board and repeat the process if needed.

Dogfennau / Adnoddau

Bwrdd Datblygu Super Mini Digilog ESP32 [pdfCyfarwyddiadau Bwrdd Datblygu Super Mini ESP32, ESP32, Bwrdd Datblygu Super Mini, Bwrdd Datblygu Mini, Bwrdd

Cyfeiriadau

• Llawlyfr Defnyddiwr