Diagram Gosod

Datgysylltwch y pŵer bob amser cyn gosod neu ailosod bylbiau a chyn glanhau neu waith cynnal a chadw arall.

1. Tynnwch y gosodiad o'i becyn gwreiddiol.
2. Separate mounting plate (1c) from canopy removing canopy screws (2f)
3. Attach mounting plate (1c) to electrical junction box (la) using screws provided (1d) in hardware package
4. I newid uchder y gosodiad, gwthio a dal gripper gwifren (2g), llithro gwifren i'r hyd a ddymunir ac yna rhyddhau gripper gwifren (2g) i'w ddiogelu (Tynnwch y wifren dros ben os oes angen)
5. Secure mounting plate (1c) to mounting surface with anchors (1f) and screws (1e)
6. Gwneud cysylltiadau trydanol cywir (du i boeth “L”, gwyn i niwtral “N”, daear i “GND”) gyda chnau gwifren (1b) wedi'u darparu mewn pecyn caledwedd
7. Attach canopy(2a) to mounting plate(1c) with canopy screws(2f) and nuts(2c) , tighten them(2f and 2c).
8. Hyd gwifren tôn gain os oes angen, trwy wthio a dal gripper gwifren (2g) ac yna addasu gwifren i'r hyd a ddymunir

1. To shorten the cable-just push the cable up, cable will be locked Automatically.
2. To length the cable-lift up on the cable and push up on the lock while keep the lock depressed, lower the cable to the desired length, release the lock to set.

A: gwthio

LED Wireless remote control operation instructions

I. Key function of remote control

1. golau dangosydd
2. Trowch ymlaen
3. disgleirdeb +
4. golau oer
5. beicio
6. Trowch i ffwrdd
7. disgleirdeb -
8. golau cynnes
9. golau nos

II. Key instructions

Trowch ymlaen: Amser byr lamp lighting, Electricity within 5 s, Long press for the code function, After power on 5 s, Long press has no effect

Trowch i ffwrdd: Amser byr lamp goes out, Electricity within 5s, Long press for clear code function, After power on 5 s, Long press has no effect;

Golau oer +:

1, Short on time, Turn the cold light fixture on one level, At the same time, the warm light lamp darkens one level, There are 15 levels of cold light from out to full light;
2, Long time, The luminaire is gradually lightened, At the same time, the warm light gradually darkens;

Golau cynnes +:

1, Short on time, The warm light fixture should be one step brighter, When the cold light lamp tywyllu un lefel, Mae 15 lefel o olau cynnes o'r tu allan i olau llawn;
2, Long time, The warm luminaire is gradually lightened, At the same time, the cold light gradually darkened;

brightness + :

1, Short on time, Heat and cold light lamps are brighter, There are 11 levels of brightness from lowest to highest;
2, Long time, Cold and warm light lamps and lanterns are gradually brightened;

brightness – :

1, Short on time, Dim the light and cold lamps, Mae 11 lefel o ddisgleirdeb o'r uchaf i'r isaf;
2, Long time, The cold and warm light lamps are gradually dimmed; cycle: Short press the loop key, The light is Warm, neutral, cold, Nightlight, Four state cycles, Press short to change the state one at a time; night lamp: Pwyswch y botwm golau nos byr, Y disgleirdeb isaf o alamp converted to Warm light;

The key light : Key indicator light, The indicator button is pressed;

Nodyn: Un o'r gosodiadau golau gwresogi ac oeri, gall cwsmeriaid ddiffinio eu hunain yn ôl y cyflenwad pŵer a lamps.

III. Functional specifications

Swyddogaeth mapio

Turn off THE LED’ s AC power for more than 10 seconds, Then turn on the LED AC power again, 4 eiliad. Long press the light button once, LED light flashes slowly once. The code successfully. Then the remote control can control the brightness, cooling and heating of the LED lights with good code.
Note: An LED light is only controlled by the last successful remote control, For example, If an LED 1 ight fixture, There is a new remote control and its code matching is successful, Then the remote control will automatically clear the code with the lamp. But a remote control can be coded and controlled with multiple LED lights,

Swyddogaeth clirio cod

Turn off THE LED’ s AC power for more than 10 seconds, Then turn on the LED AC power again, 4 eiliad, Long press the Turn off button or nightlight button once, LED light slow flash 2 time, The Ming and Qing dynasties were successful.

Note: The function of code clearing is based on the code matching between the remote control and the lamp, Am example, in the following cases, the remote control and the lamp do not have the function of code clearing, If there is no clear code function, A long press to turn off the light has no effect.
(1) The remote control is not coded with the lamp, Then there is no clear code function.
(2) When they had finished coding, they cleared the code, Then there is no clear code function.
(3) They have coded each other, But then came a new remote control that corresponded with the light fixture, Then the remote control and its code function will automatically clear, No clear code function.

1. On switch function,

Mae'r lamp is normally energized, Power on the 0.5S-2S switch, The light is Warm, neutral, cold, Nightlight, 4 state loop Twitches.

2. Power off memory function

Defnyddiwch y teclyn rheoli o bell i addasu disgleirdeb goleuadau LED, Mae disgleirdeb LED lamps a bydd gwerth cod y teclyn rheoli o bell yn cael ei gadw er cof am y rheolwr LED ar ôl 15S o bŵer, Pŵer yn ôl ymlaen ar ôl i chi golli pŵer a goleuo'r lamp at its previous brightness, And has the code remote control is still controllable.

Dogfennau / Adnoddau

Digilog E27 LED Wireless Remote Control Light Fixture [pdfCanllaw Gosod E27 LED Wireless Remote Control Light Fixture, E27, LED Wireless Remote Control Light Fixture, Remote Control Light Fixture, Light Fixture, Fixture

Cyfeiriadau

• Llawlyfr Defnyddiwr