Gosod Modiwl Rhyngwyneb Rhwydwaith Cisco Catalyst
Mae'r adran hon yn darparu gwybodaeth cyn ac yn ystod gosod Modiwlau Rhyngwyneb Rhwydwaith (NIMs) Cisco Catalyst ar Lwyfannau Ymyl Cyfres 8200 Cisco Catalyst.
Drosoddview o'r Modiwl Rhyngwyneb Rhwydwaith
The Cisco Catalyst Network Interface Module (NIM) is supported on Cisco Catalyst 8200 Series Edge Platforms.
These are the steps to install a NIM:
1. Lleolwch y slot NIM ar y panel blaen.
2. Loosen the screws to remove NIM blank cover.
3. Mewnosodwch yr NIM i'r slot.
4. Tynhau'r sgriwiau i sicrhau'r NIM yn y slot.
These are the steps to remove a NIM:
1. If the NIM is up and running, issue the following command to shut down the NIM gracefully before removing it:
hw-module subslot slot 0/2 stop
Rhybudd If you do not shut down the NIM gracefully before removing it, the NIM card could get damaged.
2. Lleolwch y slot NIM ar y panel blaen.
3. Llaciwch y sgriwiau sy'n sicrhau'r NIM.
4. Tynnwch yr NIM allan o'r slot yn ysgafn.
All module slots must have a module or blank installed for the product to work thermally and for safety purposes.
Am wybodaeth ychwanegol, gweler taflen ddata Llwyfannau Ymyl Cyfres Cisco Catalyst 8200 ar cisco.com am restr o NIMs a gefnogir ar y llwyfannau.
Tynnu a Gosod Modiwlau Rhyngwyneb Rhwydwaith
Keep the following tools and equipment while working with the Network Interface Modules (NIM)s:
- Tyrnsgriw Phillips rhif 1 neu sgriwdreifer llafn gwastad bach
- Strap arddwrn ataliol ESD
Tynnwch y Modiwl Rhyngwyneb Rhwydwaith
Cam 1 Shut down the electrical power to the slot in the device, turn off the electrical power to the device. Leave the power cable plugged-in to channel ESD voltages i'r ddaear.
Cam 2 Remove all network cables from the rear panel of the device. Using a number 1 Phillips screwdriver, loosen the captive screws on the network interface module.
Cam 3 Slide the network interface module out.
Cam 4 If you are not replacing the module, install a blank faceplate over the empty slot to ensure proper air flow.
Gosod Modiwlau Rhyngwyneb Rhwydwaith Cisco Catalyst
Cam 1 Shut down the electrical power to the slot in the router by turning off the electrical power to the router. Leave the power cable plugged in to channel ESD voltages i'r ddaear.
Cam 2 Remove all network cables from the rear panel of the device.
Cam 3 Remove the blank faceplates installed over the network interface module slot that you intend to use.
Nodyn Save blank faceplates for future use.
Cam 4 Align the module with the guides in the chassis walls or slot divider and slide it gently into the NIM slot on the device.
Cam 5 Push the module into place until you feel the edge connector seat securely into the connector on the router backplane. The module faceplate should contact the chassis rear panel.
Cam 6 Using a number 1 Phillips screwdriver, tighten the captive screws on the network interface module.
Cam 7 Connect the module to the network and re-enable the power to the slot in the device.
Gosod Modiwl Rhyngwyneb Rhwydwaith Cisco Catalyst
Dogfennau / Adnoddau
 |
Modiwl Rhyngwyneb Rhwydwaith Catalyst Cyfres CISCO 8200 [pdfCanllaw Defnyddiwr Cyfres 8200, Modiwl Rhyngwyneb Rhwydwaith Catalyst Cyfres 8200, Modiwl Rhyngwyneb Rhwydwaith Catalyst, Modiwl Rhyngwyneb Rhwydwaith, Modiwl Rhyngwyneb |