Llawlyfr Defnyddiwr Affeithwyr Auto Jack In The Box JIB_Jack_1 Antenna Ball

1. Rhagymadrodd

This manual provides instructions for the proper installation and use of your Original Jack In The Box Antenna Ball (Model: JIB_Jack_1). This accessory is designed to personalize your vehicle's antenna, assist in locating your vehicle in crowded parking areas, and can also be used as a decorative item for your rear-view mirror or desktop.

Figure 1: Original Jack In The Box Antenna Ball

2. Gwybodaeth Diogelwch

WARNING: CHOKING HAZARD - Small Parts. Not for Children Under 3 Years.

Keep this product out of reach of small children to prevent accidental ingestion or choking.

3. Cynnwys Pecyn

Dylai eich pecyn gynnwys yr eitemau canlynol:

• 1x Original Jack In The Box Antenna Ball
• 1x Optional Rear-View Mirror Hanger Accessory
• 1x Optional Desktop Bobble Spring Stand Accessory

4. Gosod & Setup

4.1. Gosod Antena

The Jack In The Box Antenna Ball is designed to fit thin, standard-style car, truck, and SUV antennas. The pre-drilled hole in the bottom of the Jack ball has a diameter of approximately 4.5mm (0.18 inches).

1. Locate your vehicle's antenna. Ensure it is a thin, standard style antenna.
2. Carefully push the antenna ball onto the tip of your antenna. Apply gentle, even pressure until it is securely seated.
3. Verify that the antenna ball is firmly attached and does not wobble excessively.

Figure 2: Antenna Ball installed on a vehicle antenna.

Ffigur 3: Examples of compatible antenna styles on various vehicles.

4.2. Enlarging the Antenna Hole (If Needed)

If your vehicle has a thicker antenna, the pre-drilled hole may need to be enlarged. Use caution during this process to avoid damaging the antenna ball.

1. Obtain a Philips-style screwdriver or any hard, tapered object.
2. Gently insert the tip of the screwdriver or tapered object into the hole at the bottom of the antenna ball.
3. Rotate the object in a circular motion while applying light pressure. Continue until the hole reaches the desired size to fit your antenna.
4. Periodically check the fit on your antenna to avoid over-enlarging the hole.

Figure 4: Instructions for enlarging the antenna ball hole.

4.3. cefn-View Mirror Hanger Installation

To use the antenna ball as a rear-view mirror hanger:

1. Locate the small screw provided with the rear-view mirror hanger accessory.
2. Carefully press the tiny screw into the top of the Jack antenna ball.
3. Attach the hanger string or loop to the screw.
4. Hang the antenna ball from your vehicle's rear-view mirror. Ensure it does not obstruct your view wrth yrru.

4.4. Desktop Bobble Spring Stand Setup

To display your antenna ball on a desktop or flat surface:

1. Insert the bottom stick of the antenna ball into the designated slot on the desktop bobble spring stand.
2. Ensure the antenna ball is securely seated on the spring stand.
3. Gosodwch y stand ar arwyneb sefydlog, gwastad.

5. Cyfarwyddiadau Gweithredu

Once installed on your antenna, the Jack In The Box Antenna Ball serves as a decorative and functional accessory. Its primary operational benefit is to help you easily identify your car, truck, or SUV in a crowded parking lot due to its distinctive appearance.

6. Gofal a Chynnal a Chadw

To maintain the appearance and longevity of your antenna ball:

• Glanhau: Wipe the antenna ball with a soft, damp cloth to remove dust and dirt. Avoid using harsh chemicals or abrasive cleaners, as these may damage the finish.
• Cysylltiad: While designed for outdoor use, prolonged exposure to extreme weather conditions (e.g., intense sunlight, heavy rain, snow) may cause fading or wear over time.
• Ffitiad Diogel: Periodically check that the antenna ball remains securely attached to your antenna, mirror hanger, or desktop stand.

7. Datrys Problemau

7.1. Antenna Ball Does Not Fit Antenna

If the antenna ball's hole is too small for your antenna, refer to Section 4.2, "Enlarging the Antenna Hole," for instructions on how to adjust the size.

7.2. Antenna Ball Feels Loose

If the antenna ball feels loose after installation, ensure it is pushed down firmly onto the antenna. If the hole was enlarged, it might have been made too wide. In such cases, a small amount of adhesive (e.g., silicone sealant) can be applied inside the hole before installation to create a tighter fit, but this will make removal more difficult.

8. manylebau

9. Gwarant a Chefnogaeth

This product is manufactured by Jack In The Box. For any questions, concerns, or support regarding your Jack In The Box Antenna Ball, please refer to the retailer where the product was purchased or visit the official Jack In The Box websafle ar gyfer gwybodaeth gyswllt gwasanaeth cwsmeriaid.

Specific warranty details may vary by retailer and region. Please retain your proof of purchase for any warranty claims.