1. Cyflwyniad a Gwybodaeth Diogelwch
This manual provides essential instructions for the safe and efficient operation of your Kenmore 385.17627 or 385.17630 sewing machine. Please read all instructions carefully before use to ensure proper function and to prevent injury.
Cyfarwyddiadau Diogelwch Pwysig:
- Datgysylltwch y peiriant o'r soced drydanol bob amser yn syth ar ôl ei ddefnyddio a chyn glanhau, tynnu gorchuddion, neu wneud unrhyw addasiadau gwasanaethu gan y defnyddiwr.
- Cadwch fysedd i ffwrdd o'r holl rannau symudol. Mae angen gofal arbennig o amgylch nodwydd y peiriant gwnïo.
- Use the proper needle plate. The wrong plate can cause the needle to break.
- Do not pull or push fabric while stitching. This may deflect the needle, causing it to break.
- Never operate the machine with any air openings blocked. Keep ventilation openings of the sewing machine and foot controller free from the accumulation of lint, dust, and loose cloth.
- Peidiwch â gweithredu lle mae cynhyrchion aerosol (chwistrellu) yn cael eu defnyddio neu lle mae ocsigen yn cael ei roi.
2. Adnabod Rhannau
Familiarize yourself with the various components of your sewing machine:
- Spool Pin: Holds the thread spool.
- Thread Guide: Directs the thread path.
- Deialu Tensiwn: Adjusts upper thread tension.
- Take-up Lever: Pulls thread from the spool and feeds it to the needle.
- Nodwydd Clamp: Secures the needle in place.
- Presser Foot: Holds fabric firmly against the feed dogs.
- Needle Plate: Flat metal plate under the needle, with markings for seam allowances.
- Feed Dogs: Move the fabric under the presser foot.
- Bobbin Winder: Winds thread onto the bobbin.
- Olwyn law: Manually raises and lowers the needle.
- Deial Dewisydd Pwyth: Chooses the desired stitch pattern.
- Reverse Lever: Allows for backstitching.
- Rheolydd Traed: Controls sewing speed.
3. Gosod
3.1 Dadbacio a Lleoli
- Tynnwch y peiriant o'i becynnu yn ofalus.
- Rhowch y peiriant ar arwyneb sefydlog, gwastad.
- Ensure adequate lighting for your work area.
3.2 Cysylltiad Pwer
- Connect the foot controller plug to the machine's receptacle.
- Plygiwch y llinyn pŵer i mewn i allfa drydanol safonol.
- Turn on the power switch, usually located on the side or back of the machine.
3.3 Needle Installation
- Turn the handwheel towards you to raise the needle to its highest position.
- Llaciwch y cl nodwyddamp sgriw.
- Mewnosodwch nodwydd newydd gyda'r ochr wastad yn wynebu cefn y peiriant.
- Push the needle up as far as it will go.
- Tynhau'r nodwydd clamp sgriw yn ddiogel.
3.4 Dirwyn Bobin
- Rhowch bobin gwag ar werthyd y bobin.
- Rhowch sbŵl o edau ar y pin sbŵl.
- Follow the thread path for bobbin winding, typically indicated by dotted lines on the machine.
- Gwthiwch werthyd y weindiwr bobbin i'r dde.
- Press the foot controller to wind the thread. Stop when the bobbin is full.
- Torrwch yr edau a gwthiwch werthyd y weindiwr bobin yn ôl i'r chwith.
4. Cyfarwyddiadau Gweithredu
4.1 Edau'r Peiriant
- Raise the presser foot and needle to their highest positions.
- Place the thread spool on the spool pin.
- Follow the numbered or solid line thread path, guiding the thread through all guides and the take-up lever.
- Gwthiwch y nodwydd o'r blaen i'r cefn.
- Insert the wound bobbin into the bobbin case, ensuring the thread unwinds in the correct direction (refer to machine markings).
- Caewch gorchudd y bobin.
- Turn the handwheel to lower and raise the needle once, catching the bobbin thread. Pull both threads under the presser foot and to the back.
4.2 Dewis Pwythau
- Trowch y deial dewis pwythau i ddewis y patrwm pwyth rydych chi ei eisiau (e.e., pwyth syth, sigsag).
- Adjust stitch length and width dials as needed for your project.
4.3 Basic Sewing Techniques
- Place fabric under the presser foot, aligning the edge with a seam guide on the needle plate.
- Gostyngwch droed y gwasgwr.
- Gently press the foot controller to begin sewing.
- To secure a seam, press the reverse lever at the beginning and end of stitching to backstitch a few stitches.
- When finished, raise the needle and presser foot, then pull the fabric out and cut the threads.
4.4 Adjusting Tension
Proper thread tension is crucial for balanced stitches. If stitches are too loose or too tight, adjust the upper thread tension dial. A balanced stitch shows equal amounts of upper and bobbin thread on both sides of the fabric.
- If upper thread lies flat on fabric: Increase upper tension (turn dial to a higher number).
- If bobbin thread lies flat on fabric: Decrease upper tension (turn dial to a lower number).
5. cynnal
Regular maintenance ensures the longevity and smooth operation of your sewing machine.
5.1 Glanhau
- Tynnwch y plwg y peiriant bob amser cyn ei lanhau.
- Remove the needle, presser foot, and needle plate.
- Defnyddiwch frwsh bach i gael gwared â lint a llwch o ardal cas y bobin a'r cŵn bwydo.
- Wipe the exterior of the machine with a soft, dry cloth.
5.2 Lubrication (Oiling)
Refer to your machine's specific oiling points, usually indicated in the original manual or by small oiling holes. Use only high-quality sewing machine oil. Do not over-oil.
- Apply a small drop of oil to designated moving parts, such as the hook race and needle bar.
- Run the machine for a few minutes on scrap fabric after oiling to distribute the oil and absorb any excess.
5.3 Amnewid Nodwydd
Replace needles frequently, especially when sewing different fabrics or if you notice skipped stitches or fabric damage. A dull or bent needle can cause significant problems.
- Follow the needle installation steps in Section 3.3.
- Always use the correct needle type and size for your fabric.
6. Datrys Problemau
Mae'r adran hon yn mynd i'r afael â phroblemau cyffredin y gallech ddod ar eu traws a'u hatebion.
| Problem | Achos Posibl | Ateb |
|---|---|---|
| Pwythau Sgipio | Incorrect needle, bent needle, improper threading, wrong needle size for fabric. | Replace needle, rethread machine, use appropriate needle. |
| Thread Breakage (Upper) | Improper threading, too much upper tension, burr on needle plate, poor quality thread. | Rethread, adjust tension, check for burrs, use quality thread. |
| Thread Breakage (Bobbin) | Improperly wound bobbin, bobbin inserted incorrectly, too much bobbin tension. | Rewind bobbin, reinsert correctly, check bobbin case tension. |
| Pwcio Ffabrig | Too much tension, incorrect stitch length, dull needle. | Addaswch y tensiwn, cynyddwch hyd y pwyth, ailosodwch y nodwydd. |
| Jamio Peiriant | Thread tangled in bobbin area, lint buildup, bent needle. | Clear bobbin area, clean machine, replace needle. |
Os yw problemau'n parhau ar ôl rhoi cynnig ar yr atebion hyn, cysylltwch â chymorth cwsmeriaid.
7. manylebau
- Rhifau Model: 385.17627, 385.17630
- Math: Peiriant Gwnïo Mecanyddol
- Ffynhonnell Pwer: AC 120V, 60Hz (Standard Household Outlet)
- Modur: Modur Cyffredinol
- Mathau o Bwythau: Straight, Zigzag, and various utility stitches (specifics depend on model variant)
- Needle System: 15x1 (HAx1)
- Pwysau: Approximately 15-20 lbs (varies by model)
- Dimensiynau: Approximately 16" L x 7" W x 12" H (varies by model)
8. Gwarant a Chefnogaeth
For specific warranty information, please refer to the warranty card included with your original purchase or contact the retailer where the machine was acquired. Kenmore products typically come with a limited warranty covering manufacturing defects.
Cefnogaeth i Gwsmeriaid:
If you require further assistance, have questions not covered in this manual, or need to arrange for service, please contact Kenmore customer support or your authorized service center. Have your model number and serial number ready when contacting support.
For the most up-to-date contact information, please visit the official Kenmore websafle neu ymgynghorwch â'ch dogfennaeth prynu.
