Android Car Player Instruction Manual

Android Car Player Instruction

MANYLEB

• power Supply Volllgo
• Y Defnydd Cyfredol Uchaf
• Pŵer Allbwn Uchaf

1. UNIVERSAL MACHINE WIRING DIAGRAM
   
2. SPECIAL VEHICLE WIRING DIAGRAM

RHAGOFALAU ENNILL

• 10P: Connect the reversing video input. Note: The two short wires above this line are the Bluetooth antenna and the WIFI antenna. Even if the reversing camera is not connected, this cable needs to be connected to the machine, otherwise Bluetooth and WIFI will not be connected, and carplay and Android auto will not be connected.
• 6P: Connect USB-2.
• 4P. Connect USB-1.
• 8P: Connect the CANBUS box. Note: When the product you purchased has a CANBUS box, you must connect the CANBUS box to the
• 8Pin socket on the body, otherwise some of the original car functions will not be available.
• 12P.360-degree panoramic reversing image (only supported by some models).
• 20P.RCA plug. The AMP CONT line needs to pay attention to: If your car supports speakers such as JBL or BOSE, you may need to connect this cable to the on-off control of your car’s power amplifier, and try connecting it when there is no sound.

DULL GOSOD CAMERA WRTH GEFN

CYFARWYDDIADAU WEFRIO CORD PŴER CYFFREDINOL

Tips The wiring harness colors of some models may be different. Please refer to the wire labels and the positions on the plugs and sockets.

UNIVERSAL MACHINE POWER PIN DEFINITION

RHEOLAETHAU OLWYN LLYWIO DYSGU
Pwyswch a dal botwm ar olwyn llywio'r car gwreiddiol a darganfyddwch eicon y botwm sy'n cyfateb i swyddogaeth y botwm ar yr olwyn lywio. Cliciwch yr eicon i newid y lliw, mae dysgu'n llwyddiannus.

iPHONE Mirrorlink (Dim ond rhai modelau sy'n cefnogi)
Pan fydd y ddyfais wedi'i phlygio i'r iPhone, bydd cynnwys sgrin y ffôn yn cael ei daflunio ar sgrin y car.

Android Mirrorlink (Dim ond rhai modelau sy'n cefnogi)
When using an Android device, after connecting the USB data cable. you will be prompted to install the APP software. After installation, Plug the data cable again, it will enter the screen mirroring mode. And it can be operatedon both the player screen and the phone screen. Only the image transfer is successful at this time. The sound can only be  transmitted after the Bluetooth connection is successful.

Apple Car Play (Only some models support)

1. Wired connection: Just connect the USB data cable, and then it will auto matically enter the CarPlay interface.
2. Wireless connection: first tum on the bluetooth and wifi functions of the mobile phone. and then connect the bluetooth. Then it will automatically enter the CarPlay interface.
   (Note. The signal is transmitted through wifi at this ime, so even if the Bluetooth function is tumed off, it will be transmitted normally. When the wifi function is turned off. CarPlay will be disconnected.)

Android Auto (Dim ond rhai modelau sy'n cefnogi)
Nid yw'r nodwedd hon yn cael ei chefnogi ym mhob gwlad, ac “Mae angen i wasanaethau Google Play fod ar gael yn lleol.

1. Angen lawrlwytho a gosod "Android Auto" software in “Google Play”
2. Rhaid defnyddio ffôn symudol gyda Android 6.0 neu uwch. Rhaid defnyddio cysylltiad cebl data dilys.
3. Cysylltiad â gwifrau: Cysylltwch y cebl data USB yn unig, ac yna bydd yn mynd i mewn i ryngwyneb Android Auto yn awtomatig.
4. Wireless connection: First turn on the Bluetooth and wifi functions of the mobile phone. and then connect the Bluetooth. Then it will automatically enter the Android Auto interface. (Note: The signal is transmitted through wifi at this time, so even if the Bluetooth function is turned off, it will be transmitted normally. When the wifi function is turned off, Android Auto will be disconnected.)

PROBLEMAU CYFFREDIN A THRWSIO SYML

Methu cychwyn fel arfer

1. “Yellow” “Red” “Black’ this 3 lines only connected 2 line of them, so it will not start, it should be that the yellow line is connected to the positive pole, red line to the key control line, black to the negative pole, less connection or wrong connection does not boot.
2. Ni ellir cysylltu'r llinell car wreiddiol a'r gwifrau uned â'r lliw, nid yw lliw y llinell gar wreiddiol yn safonol, os ydych chi'n cysylltu fel yna ni ellir ei droi ymlaen yn unig ond gall hefyd losgi.
3. Ni ellir plygio'r plwg car gwreiddiol yn uniongyrchol i'r uned newydd, hyd yn oed os yw'n plygio i mewn, ni ellir ei ddefnyddio. fel arall ni fydd yn cael ei droi ymlaen na'i losgi.
4. Mae'r 3 gwifren wedi'u cysylltu'n iawn, ond nid yw'n cychwyn. Gwiriwch a yw'r ffiws ar y llinell felen wedi torri. Os nad oes problem gyda'r ffiws, trowch y gwifrau melyn a choch gyda'i gilydd. Trowch yr allwedd ymlaen a gwasgwch botwm pŵer yr uned i weld a ellir ei droi ymlaen.
5. Every time you change the fuse, it burns. Please don’t change it again The reason is that when you first connect the positive and negative poles, the protection circuit of the unit is short-circuited. The unit can be repairedunder the guidance of our master. No basis can only be returned to the after-sales or new unit. If these are no problem, or also don’t boot, please make the final step to confirm, find a 12V battery or 12V power supply yellow and “red twist together with the positive, black to the negative pole. press the button check if it can boot or no, if you can boot, it showed that the original car line is not right connect, or there is a problem with the car line.  If it can’t be boot, the unit is broken. Does not boot unit, check the line carefully, do not blindly suspect the unit problem.

Cau i lawr yn awtomatig

1. Gwall cysylltu'r cebl: Os yw'r cebl glas (cyflenwad pŵer antena awtomatig) wedi'i gysylltu â chebl pŵer yr uned, bydd cau awtomatig yn digwydd. Dilynwch y dull gwifrau cywir i ddatrys y broblem.
2. Mae'r cyftage yn ansefydlog: dewch o hyd i 12V-5A pa un yw'r cyflenwad pŵer a'i ail-brofi i weld a fydd yn cau'n awtomatig. Os na fydd yn cau i lawr yn awtomatig ar ôl y prawf, a fyddech cystal â disodli'r cyflenwad pŵer. Os bydd yn cau i lawr yn awtomatig, mae'n broblem gyda'r uned.

Mae sŵn

1. Mae pŵer y siaradwr gwreiddiol yn rhy fach. Pan fydd cyfaint yr uned yn cael ei droi i fyny. bydd swn.
   Ateb: Wrth ddisodli'r siaradwr neu wrando ar y gân, ni ddylai'r gyfrol fod yn rhy fawr.

Mae'r cebl siaradwr wedi'i seilio.
Ateb: Cymerwch y cebl siaradwr haearn. Wedi'i gysylltu'n uniongyrchol â chebl siaradwr yr uned.

Ni ellir defnyddio rheolaeth bell

1. Test method Turn on the camera of the mobile phone and align the light of the remote control then press the button of the remote control to see if the phone will light up. If it is not lit there will be no power. Replace the battery: If it is it there is electricity, which proves that there is no problem with the remote control.

Ni ellir cadw gosodiadau ( dim cof )

1. Mae'r llinell felen a'r llinell goch wedi'u cysylltu â'i gilydd (melyn ar wahân i bositif, coch i reolaeth allweddol).
2. Mae melyn a choch yn cael eu gwrthdroi (dim ond newid safle).

Bluetooth ddim yn gweithio
Trowch y peiriant ymlaen, chwiliwch am enw Bluetooth y peiriant gan ddefnyddio Bluetooth y ffôn symudol, ac yna cliciwch ar Connect, ar ôl cysylltu, gallwch ateb galwadau neu chwarae caneuon trwy Bluetooth.

Mae'r cynnyrch yn allyrru mwg
Amnewid y ffiws Fuse, os na ellir datrys y broblem, mae'r cylched mewnol wedi'i losgi. Mae angen gwasanaeth ôl-werthu.

Ni ellir addasu'r sain

1. Ailosodwch yr uned neu dad-blygiwch y llinyn pŵer a'i blygio i mewn.
2. The Volume knob is broken, and it can be replaced.

Nid yw'r camera gwrthdroi yn dangos

1. Gwifrau anghywir neu weirio ar goll.

Dull cysylltu camera:

1. Dod o hyd i ategolion: 1 camera + 1 llinyn pŵer + 1 cebl fideo.
2. Find the port of the wiring. First find the reverse control line on the power line of the unit. The control line is a pink line. Connect this line to the positive pole of 12V and the screen will turn blue. And then find the back of the unit the CAM video input interface, find the positive and negative of the backup light.
3. Mae dwy soced ar y camera, mae'r soced coch wedi'i gysylltu â'r cebl pŵer, mae'r melyn yn cael ei fewnosod yn y cebl fideo, mae gwifren goch y cebl pŵer a gwifren y cebl fideo yn cael eu sgriwio gyda'i gilydd ar begwn positif y cefn lamp, and the black wire of the power cable is not used. connected, the other end of the video cable is connected to the CAM video input interface on the back of the unit. The red line coming out of the video line is connected to the reversing control line of the power line.
4. Mae'r camera wedi torri. Os bydd y lamp sydd wedi'i wifro'n iawn i'r camera heb ei oleuo. caiff ei dorri a'i ddisodli gan un newydd.

Ni ellir chwarae dyfeisiau USB
Fformatiwch y ddisg fflach USB, a'r file system yn cael ei dewis fel: FAT32, ail-lawrlwytho ar neu ddwy gân a rhoi cynnig arall arni. Os nad yw'n gweithio o hyd, amnewidiwch y gyriant fflach USB.

Nid yw FM yn derbyn yr orsaf radio

1. The antenna plug is not fully inserted, the antenna is disconnect or the line is disconnected.
2. Search station, press AS will automatically search or press the before or after button. Can’t solve the above 2 points. Please unplug the antenna plug and find a screwdriver or a metal strip to insert into the antenna.

Nid oes sain yn union ar ôl ei osod
Dear customers, the unit has been tested before shipment. If there is no sound, it is usually a wiring error or the original car speaker wire is short- circuited with iron. According to the steps to check it:

1. Gwiriwch a yw'r cebl siaradwr yn fyr-gylchred ac wedi'i gysylltu. Ailgysylltu os oes gennych unrhyw gylched byr.
2. Check how many speaker cables according to the original speaker cable if there are only 2 speaker cables, to prove that the original car line does not match our unit, you need to re-route the original car line. One speaker must lead to 2 speaker wires. 2 speakers must be have 4 speaker cables to available.

Nid oes sain ar ôl ychydig
Disconnect all the speaker cable from the unit (do not remove them), and then find an external speaker to receive the gray and purple of the tail line of the unit.Check any group, and then try to see if there is any sound If there is a sound, it is proven that the car’s speaker line is short-circuited with iron or the speaker is damaged. If there is no sound, the unit is broken.

Awgrymiadau: If the device is updated, the functions are subject to change without prior notice