Ffrâm Sengl Statig Boost B2-SSCT

Manylebau

• Table feet: 2 pcs
• Centre bracket: 1 pc
• Column (right): 1 pc
• Center rails: 2 pcs
• Allen Wrench (4mm): 1 pc
• Allen Wrench (5mm): 1 pc

Cyfarwyddiadau Defnydd Cynnyrch

Cyfarwyddiadau Cymanfa

1. Cam 1: Llaciwch y bolltau sydd wedi'u gosod ymlaen llaw ac addaswch hyd y ffrâm uchaf i gyd-fynd â maint top y bwrdd.
2. Cam 2: Insert the Column into the top frame, fix the lifting column with 4pcs screws M6x12.
3. Cam 3: Place the table feet on the Column, rotate it to align, then tighten the pre-installed bolt.
4. Cam 4: Rhowch y braced ochr ar y ffrâm uchaf a thynhau'r bolltau.
5. Cam 5: Mount the tabletop and fix it with 14 pcs screws ST4x20; Fix the centre bracket with 2 pcs screws M6x10. Tighten the pre-installed bolts on the top frame.

Gosod Hambwrdd Cebl

1. Cam 1: Fix the cable tray (B2-SSCT) to the cable tray arms (B2-SSARM) with 8 pcs M6x10 screws.
2. Cam 2: Gosodwch y bracedi U i ffrâm y ddesg gyda 4 darn o sgriwiau M8x10. Mowntiwch y hambwrdd cebl i ffrâm y ddesg a'i drwsio gyda 6 darn o sgriwiau M6x10.

Gosod Panel Sgrin (Sgrin Preifatrwydd Shush30)

1. Cam 1: Insert the tapped plates into the screen panel (plates can be found in the B2-SBRAC carton).
2. Cam 2: Gosodwch y bracedi sgrin (B2-SBRAC) i'r Allwthiad Shush30 gydag 8 darn o sgriwiau M5x6.
3. Cam 3: Trwsiwch y bracedi sgrin (B2-SBRAC) i ffrâm y ddesg gyda 10 darn o sgriwiau M6x10.

Eco Panel Screen Panel Installation

1. Cam 1: Install the screen brackets (B2-SBRAC) on the cable tray arm (B2-SSARM) with 10 PCS M6x10 Screws. The direction as the photos display.
2. Cam 2: Place the EPS panel on the screen brackets using a 6mm drill bit (not included), drill out holes in the Eco Panel Screen in line with the back-to-back screen bracket holes.
   • Place 8 x Double Ended Bolts M5*32mm -6mm through the screen bracket (B2-SBRAC) holes and the holes you have created in the Eco Panel Screen. Tighten the double-ended bolt with an Allen key.

Rhannau cydran

RHIF.	Enw'r Gydran	PCS
1	Traed bwrdd	2
2	Colofn (dde)	1
3	Bollt: M6x12	5
4	Sgriw: ST4x20	22
5	Cromfachau ochr	2
6	Pad rwber	14
7	Ffrâm uchaf-1	1
8	Bollt: M6x10	3

RHIF.	Enw'r Gydran	PCS
9	Braced canol	1
10	Rheiliau canol	2
11	Ffrâm uchaf-2	1
12	Colofn (chwith)	1
13	Allen Wrench (4mm)	1
14	Allen Wrench (5mm)	1
15	Tei Cebl	5

Cyfarwyddiadau Cymanfa

1. Cam 1
   • Llaciwch y bolltau sydd wedi'u gosod ymlaen llaw ac addaswch hyd y ffrâm uchaf i gyd-fynd â maint top y bwrdd.
2. Cam 2
   • Insert the Column into the top frame, fix the lifting column with 4pcs screws M6x12.
3. Cam 3
   • Place the table feet on the Column and rotate it and make it align, then tighten the pre-installed bolt.
4. Cam 4
   • Rhowch y braced ochr ar y ffrâm uchaf a thynhau'r bolltau.
5. Cam 5
   • Gosodwch ben y bwrdd a'i drwsio gyda 14 darn o sgriwiau ST4x20;
   • Fix the centre bracket with 2 pcs of screws M6x10.
   • Tynhau'r bolltau sydd wedi'u gosod ymlaen llaw ar y ffrâm uchaf.

Gosod hambwrdd cebl

1. Cam 1
   • Trwsiwch y hambwrdd cebl (B2-SSCT) i freichiau'r hambwrdd cebl (B2-SSARM) gydag 8 darn o sgriwiau M6x10.
   • Cam 2
   • Gosodwch y cromfachau U i'r ffrâm ddesg gyda sgriwiau 4 pcs M8x10.
   • Gosodwch yr hambwrdd cebl i ffrâm y ddesg a'i drwsio â sgriwiau 6 pcs M6x10

Gosod panel sgrin (Sgrin Preifatrwydd Shush30)

1. Cam 1
   • Insert the tapped plates into the screen panel ( plates can be found in the B2-SBRAC carton )
2. Cam 2
   • Gosodwch y bracedi sgrin (B2-SBRAC) i'r Allwthiad Shush30 gydag 8 darn o sgriwiau M5x6.
3. Cam 3
   • Trwsiwch y bracedi sgrin (B2-SBRAC) i ffrâm y ddesg gyda 10 darn o sgriwiau M6x10.

Gosod panel sgrin EPS (Panel Eco 900mm U)

1. Cam 1
   • Install the screen brackets(B2-SBRAC) on the cable tray arm (B2-SSARM)with 10 PCS M6x10 Screws
   • The direction as the photos display.
2. Cam 2
   • Rhowch y panel EPS ar y cromfachau sgrin
   • Using a 6mm drill bit ( not included ), drill out holes in Eco Panel Screen in line with to back screen bracket holes ( Note: Carbide Drill Bits Work Best For PET panel )
   • Place 8 x Double Ended Bolts M5* 32mm – 6mm through the screen bracket ( B2-SBRAC ) holes and the holes you have created in the Eco Panel Screen. Tighten the double-ended bolt with the Allen key.

Cwestiynau Cyffredin

How many table feet are included in the package?

There are two table feet included.

What size screws are used for fixing the lifting column?

You need to use 4pcs of screws M6x12 for fixing the lifting column.

How many pcs of Allen Wrench are provided?

There is one Allen Wrench of 4mm and one Allen Wrench of 5mm provided in the package.

Dogfennau / Adnoddau

Ffrâm Sengl Statig Boost B2-SSCT [pdfLlawlyfr Cyfarwyddiadau B2-SSCT, B2-SSARM, B2-SBRAC, B2-SSCT Ffrâm Sengl Statig, B2-SSCT, Ffrâm Sengl Statig, Ffrâm Sengl, Ffrâm

Cyfeiriadau

• Llawlyfr Defnyddiwr