1. Rhagymadrodd
The SENSTREE WTC100 is a wireless digital plug-in thermostat designed for automatic temperature control of various electrical heating or cooling appliances. It allows users to set target temperatures to automatically activate or deactivate connected devices, maintaining a stable environment. This manual provides essential information for the safe and effective use of your WTC100 controller.
2. Gwybodaeth Diogelwch
- Darllenwch yr holl gyfarwyddiadau cyn eu defnyddio.
- Ensure the device is properly grounded. The receiver features a 3-prong grounded terminal.
- Do not exceed the maximum load capacity of 15A (1500W at 110V, 3000W at 220V).
- Do not immerse the remote controller or receiver in water or expose them to excessive moisture.
- Cadwch allan o gyrraedd plant.
- Do not disassemble or attempt to repair the device. Contact customer support if service is required.
- Replace batteries in the remote controller promptly when the low battery indicator appears to ensure continuous operation.
3. Cynnyrch Drosview
The WTC100 system consists of two main components: a wireless remote controller and a plug-in receiver outlet.
Figure 3.1: WTC100 Remote Controller and Plug-in Receiver
3.1. Rheolwr o Bell
- Arddangosfa LCD: Shows current temperature, set temperatures, and operating mode.
- Botymau Rheoli: SET, Up, Down, M (Mode) for configuration.
- Synhwyrydd Tymheredd Cynwysedig: Detects ambient temperature for control.
- Adran Batri: For 2x AAA batteries (not included).
Figure 3.2: Remote Controller with integrated temperature sensor
3.2. Plug-in Receiver
- Allfa Bwer: Connects to your heating or cooling appliance.
- Botwm YMLAEN / DIFFODD y llawlyfr: Allows manual control of the connected appliance.
- Golau Dangosydd: Shows power status and connection.
Figure 3.3: Receiver with plug and specification label
4. Gosod
4.1. Install Batteries in Remote Controller
- Open the battery compartment cover on the back of the remote controller.
- Mewnosodwch ddau (2) fatri AAA, gan sicrhau'r polaredd cywir (+/-).
- Caewch y clawr adran batri.
4.2. Plug in the Receiver
- Plug the WTC100 receiver into a standard 3-prong wall outlet.
- Plug your heating or cooling appliance into the outlet on the receiver.
4.3. Paru (os oes angen)
The remote controller and receiver are typically pre-paired at the factory. If they do not connect automatically, follow these steps:
- Ensure both the remote and receiver are powered on.
- Press and hold the power button on the receiver for 3-5 seconds until the indicator light flashes.
- Within 10 seconds, press any button on the remote controller. The indicator light on the receiver will stop flashing and remain solid, indicating successful pairing.
5. Cyfarwyddiadau Gweithredu
5.1. Pŵer YMLAEN / I FFWRDD
- Rheolydd o Bell: The remote is always on to display temperature.
- Derbynnydd: Press the power button on the receiver to manually turn the connected appliance ON or OFF.
5.2. Newid Unedau Tymheredd (°C/°F)
Figure 5.1: Switching between Celsius and Fahrenheit
To switch between Celsius (°C) and Fahrenheit (°F), press and hold the 'UP' arrow button on the remote controller for approximately 3 seconds.
5.3. Setting Operating Mode (Heating/Cooling)
Figure 5.2: Cooling and Heating Mode Switchable
Press the 'M' (Mode) button on the remote controller to toggle between Heating Mode and Cooling Mode. The display will indicate the active mode.
5.4. Setting Target Temperatures
The WTC100 allows you to set both an 'ON' temperature and an 'OFF' temperature for precise control.
- Press the 'SET' button once. The 'ON' temperature will flash. Use the 'UP' or 'DOWN' arrows to adjust the desired 'ON' temperature.
- Press the 'SET' button again. The 'OFF' temperature will flash. Use the 'UP' or 'DOWN' arrows to adjust the desired 'OFF' temperature.
- Press 'SET' a third time or wait a few seconds for the settings to save automatically.
Heating Mode Example: If 'ON' is set to 68°F and 'OFF' is set to 72°F, the heater will turn on when the temperature drops to 68°F and turn off when it reaches 72°F.
Video 5.3: Demonstration of setting Heating Mode with the WTC100. This video illustrates how to configure the thermostat to activate a heating device when the temperature falls below a set point and deactivate it when it rises above another set point.
Cooling Mode Example: If 'ON' is set to 78°F and 'OFF' is set to 74°F, the cooling device will turn on when the temperature rises to 78°F and turn off when it drops to 74°F.
Figure 5.4: WTC100 controlling a window air conditioner in Cooling Mode
6. cynnal
- Glanhau: Wipe the remote and receiver with a soft, dry cloth. Do not use abrasive cleaners or solvents.
- Amnewid Batri: When the low battery indicator appears on the remote's display, replace both AAA batteries immediately to ensure accurate temperature readings and continuous control.
7. Datrys Problemau
| Problem | Achos Posibl | Ateb |
|---|---|---|
| Remote display is blank or dim. | Batris isel neu farw. | Replace AAA batteries in the remote controller. |
| Receiver not responding to remote. | Heb ei baru, allan o gyrraedd, neu ymyrraeth. | Re-pair the remote and receiver (see Section 4.3). Ensure remote is within 100m (open space) of the receiver. Avoid strong electromagnetic interference. |
| Connected appliance not turning ON/OFF at set temperatures. | Incorrect mode (Heating/Cooling), incorrect set temperatures, or appliance issue. | Verify the correct operating mode is selected. Check and adjust 'ON' and 'OFF' temperatures. Ensure the appliance itself is functioning correctly. |
| Mae'n ymddangos bod y darlleniad tymheredd yn anghywir. | Remote sensor obstructed or exposed to direct heat/cold. | Ensure the remote controller's sensor (located at the top) is not covered and is placed in an area representative of the desired ambient temperature. |
| Larwm yn swnio'n aml. | High/low temperature alarm thresholds reached. | The WTC100 features high and low temperature alarms. Consult the full product manual for specific alarm settings and how to adjust or temporarily mute them. |
8. manylebau
| Nodwedd | Manylyn |
|---|---|
| Enw Model | WTC100 |
| Mewnbwn Voltage | 100-240VAC |
| Allbwn Max Cyfredol | 15A |
| Pŵer Allbwn Uchaf | 1500W@110V / 3000W@220V |
| Math Rheoli Tymheredd | Rhaglenadwy |
| Technoleg Cysylltedd | Di-wifr (RF) |
| Pellter Rheolaeth Anghysbell | Hyd at 100m (man agored) |
| Synhwyrydd Tymheredd | Built-in to Remote Controller |
| Math Arddangos | LCD gyda Backlight |
| Power Source (Remote) | 2 x Batris AAA (heb eu cynnwys) |
| Mounting Type (Remote) | Wall Mount, Handheld |
9. Gwarant a Chefnogaeth
SENSTREE products are designed for reliability and performance. For warranty information, technical support, or service inquiries, please refer to the contact information provided with your product packaging or visit the official SENSTREE websafle. Cadwch eich prawf prynu ar gyfer hawliadau gwarant.