GoControl WS15Z5-1 Z-Wave(R) Wall Switch User Manual

Rhagymadrodd

Thank you for choosing the GoControl WS15Z5-1 Z-Wave Wall Switch. This smart switch allows you to control your lighting or other connected loads remotely via a Z-Wave network, as well as manually. It integrates seamlessly into your smart home system, providing convenience and energy efficiency. Please read this manual carefully before installation and operation to ensure proper use and safety.

Gwybodaeth Diogelwch

RHYBUDD: Risk of Electric Shock. Installation should be performed by a qualified electrician. Disconnect power at the circuit breaker or fuse box before installation or servicing. Use only copper wire for connections. Do not exceed the maximum load ratings.

• Ensure power is OFF at the circuit breaker before installation.
• Bwriedir gosod y ddyfais hon yn unol â'r Cod Trydan Cenedlaethol a rheoliadau lleol.
• Do not use in wet locations or where directly exposed to water.
• Ar gyfer defnydd dan do yn unig.

Cynnwys Pecyn

• GoControl WS15Z5-1 Z-Wave Wall Switch
• Sgriwiau Gosod
• Wire Nuts (may vary by package)
• Llawlyfr Defnyddiwr (y ddogfen hon)

Gosod a Gosod

Follow these steps carefully to install your GoControl Z-Wave Wall Switch.

1. Wiring the Switch

1. Diffoddwch y Pŵer: Locate the circuit breaker controlling the switch you are replacing and turn it OFF. Verify power is off by attempting to turn on the light or appliance.
2. Tynnu'r Hen Switsh: Carefully remove the existing wall plate and switch from the wall box. Disconnect the wires from the old switch, noting which wire was connected to which terminal (Line, Load, Neutral, Ground).
3. Adnabod Gwifrau:
   • Line (Hot): Fel arfer yn ddu, yn dod o'r torrwr cylched.
   • Llwyth: Usually black, going to the light fixture or appliance.
   • Niwtral: Usually white, often bundled together in the back of the box. (Required for Z-Wave switches).
   • Tir: Fel arfer copr gwyrdd neu noeth.
4. Cysylltu Switsh Newydd: Connect the wires to the GoControl WS15Z5-1 switch terminals as follows:
   • Cysylltwch y Llinell wire to the terminal marked "LINE".
   • Cysylltwch y Llwyth wire to the terminal marked "LOAD".
   • Cysylltwch y Niwtral wire to the terminal marked "NEUTRAL".
   • Cysylltwch y Daear wire to the terminal marked "GROUND".

   Ensure all connections are secure. If you are unsure about wiring, consult a qualified electrician.

5. Mowntio Switsh: Carefully push the wired switch into the wall box. Secure it with the provided screws.
6. Gosod Wall Plat: Attach the new or existing wall plate.
7. Adfer Pwer: Trowch y pŵer yn ôl YMLAEN wrth y torrwr cylched.

Ffigur 1: Blaen view of the GoControl WS15Z5-1 Z-Wave Wall Switch.

2. Cynhwysiant Ton-Z (Paru)

To integrate the switch into your Z-Wave network, you need to "include" it with your Z-Wave controller.

1. Put your Z-Wave controller into Inclusion/Pairing mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle unwaith. The LED indicator on the switch will blink to confirm inclusion mode.
3. The controller will confirm successful inclusion. The switch's LED will stop blinking and remain solid or turn off, depending on its status.
4. If inclusion fails, refer to the Troubleshooting section or try "Exclusion" first.

Figure 2: The Z-Wave logo, indicating compatibility with Z-Wave networks.

Gweithredu'r switsh

Rheolaeth â Llaw

• Gwasgwch y brig of the paddle to turn the connected load ON.
• Gwasgwch y gwaelod of the paddle to turn the connected load ODDI AR.

Rheoli Z-Ton

Once included in your Z-Wave network, you can control the switch remotely using your Z-Wave controller, hub, or compatible smart home application.

• Use your Z-Wave app or controller interface to toggle the switch ON/OFF.
• The switch supports standard Z-Wave commands for basic on/off functionality.

Figure 3: GoControl products integrate with smart home systems for control via smartphones and other devices.

Figure 4: Diagram illustrating GoControl's integration across various smart home categories like Climate, Lighting, Security, Sensors, and Access.

Cynnal a chadw

The GoControl WS15Z5-1 Z-Wave Wall Switch requires minimal maintenance.

• Glanhau: To clean the switch, wipe it with a soft, damp brethyn. Peidiwch â defnyddio glanhawyr neu doddyddion sgraffiniol.
• Diweddariadau Cadarnwedd: Check the GoControl website or your Z-Wave controller's documentation for information on potential firmware updates.
• Gofal Cyffredinol: Gwnewch yn siŵr nad yw'r switsh yn agored i leithder gormodol na thymheredd eithafol.

Datrys problemau

Z-Wave Exclusion (Removing from Network)

If you need to remove the switch from your Z-Wave network, follow these steps:

1. Put your Z-Wave controller into Exclusion mode. (Refer to your Z-Wave controller's manual for specific instructions).
2. On the GoControl WS15Z5-1 switch, quickly press the top or bottom paddle unwaith. The LED indicator will blink to confirm exclusion mode.
3. The controller will confirm successful exclusion. The switch's LED will stop blinking.

Manylebau

Gwarant a Chefnogaeth

GoControl products are designed for reliability and performance. For warranty information, technical support, or further assistance, please visit the official GoControl websafle neu cysylltwch â'u hadran gwasanaethau cwsmeriaid.

Websafle: www.gocontrol.com

Gwneuthurwr: GOCONTROL