Boxlight Replacement Lamp Llawlyfr Defnyddiwr Modiwl

Gwybodaeth Ddiogelwch Bwysig

Mae'r bwlb yn y lamp contains Mercury (Hg). Please dispose of in accordance with local, state, or federal laws. Do not dispose of with regular household waste.

• Always disconnect the projector from the power outlet before attempting any installation or maintenance.
• Allow the projector to cool down completely (at least 30 minutes) before replacing the lamp. Hot lamps can cause severe burns.
• Avoid touching the glass surface of the new lamp directly with bare hands. Oils from your skin can reduce lamp life. Use gloves or a clean cloth if necessary.
• Peidiwch â gorfodi'r lamp module into place. If it does not fit easily, recheck the orientation and ensure it is the correct lamp for your projector model.
• Never operate the projector with the lamp clawr wedi'i dynnu.
• Cadw'r lamp module out of reach of children.

Cyfarwyddiadau Gosod

1. Pŵer i ffwrdd a datgysylltu: Ensure your Boxlight projector is turned off and completely unplugged from the power source.
2. Oeri i lawr: Allow the projector to cool down for at least 30 minutes. The lamp operates at high temperatures and can cause burns if handled while hot.
3. Locate Lamp Clawr: Refer to your projector's user manual to locate the lamp compartment cover. This is typically secured by one or more screws.
4. Dileu Lamp Clawr: Using a suitable screwdriver, carefully remove the screw(s) securing the lamp cover and then remove the cover.
5. Unscrew Old Lamp: Yr hen lamp module will be secured by one or more screws. Unscrew these fasteners.
6. Tynnu Hen Lamp: Gently pull the handle on the old lamp module to slide it out of the projector. Be careful not to drop it.
7. Mewnosod New Lamp: Carefully insert the new Boxlight replacement lamp module into the projector, ensuring it slides smoothly into place. Do not force it.
8. Secure New Lamp: Fasten the new lamp module with the screw(s) you removed earlier. Ensure it is securely seated.
9. Amnewid L.amp Clawr: Ail-gysylltu'r lamp compartment cover and secure it with its screw(s).
10. Pŵer Ailgysylltu: Plug the projector back into the power outlet.
11. Ailosod Lamp Amserydd: Consult your projector's user manual for instructions on how to reset the lamp timer. This is crucial for accurate lamp life tracking.

Canllawiau Gweithredu

• Cau i lawr yn gywir: Always allow the projector to complete its cooling cycle after use before unplugging it. Abrupt power cuts can shorten lamp bywyd.
• Awyru: Ensure the projector has adequate ventilation. Blocked vents can lead to overheating and reduced lamp bywyd.
• Osgoi Beiciau Ymlaen / Allan yn Aml: Turning the projector on and off frequently can stress the lamp a lleihau ei oes.
• Eco Mode (if available): If your projector has an "Eco Mode" or similar power-saving setting, using it can extend lamp bywyd.

Cynnal a chadw

• Glanhau hidlydd aer: Regularly clean or replace your projector's air filter as per your projector's manual. A clogged filter can cause the projector to overheat, negatively impacting lamp bywyd.
• Tynnu Llwch: Keep the projector free from dust. Use a soft, dry cloth to wipe the exterior. Do not use abrasive cleaners or solvents.
• Lamp Trin: Wrth drin y lamp module, always hold it by its housing, not the bulb itself.

Datrys problemau

If you encounter issues after installing the new lamp, ystyriwch y canlynol:

• Lamp Ddim yn goleuo:
  • Sicrhau y lamp module is fully seated and secured with its screws.
  • Gwiriwch y lamp cover is correctly installed and secured. Many projectors have a safety switch that prevents operation if the cover is open.
  • Check that the projector is properly plugged into a working power outlet.
• Dim Image or Poor Color:
  • Cadarnhewch y lamp timer has been reset. If not, the projector might still be operating under the assumption of an old, worn-out lamp.
  • Check projector settings for brightness or picture modes.
  • Ensure the projector lens is clean.
• "Lamp Error" Message:
  • This often indicates the lamp is not properly installed or the lamp cover is not secured. Re-check installation steps.
  • If the error persists, the lamp itself might be faulty. Contact customer support.

For further assistance, refer to your projector's original user manual or contact Boxlight customer support.

Manylebau Cynnyrch

Gwybodaeth Gwarant

This Boxlight replacement lamp module is covered by a Gwarant Diwrnod 180 o ddyddiad y pryniant. Mae'r warant hon yn cwmpasu diffygion mewn deunyddiau a chrefftwaith o dan ddefnydd arferol. Cadwch eich prawf prynu ar gyfer hawliadau gwarant.

For warranty service or inquiries, please contact the seller or manufacturer directly.

Cefnogaeth i Gwsmeriaid

If you require further assistance, have questions about installation, or need to report an issue, please contact the retailer where you purchased this product or the manufacturer, Arclyte Tech. (Boxlight's manufacturer).

When contacting support, please have your product model number (ACTG042) and proof of purchase readily available.